Witam Załącz wagę z wciśniętym switchem. Na wyświetlaczu pojawi się CAL 1 Strzałkami góra lub dół ustaw Cal 3 potem naciśnij enter na wyświetlaczu pojawi się Zero- kalibracja zera - naciśnij enter pojawi się Mid kładziesz 1/3 pełnego obciążenia i enter potem pojawi się full - kładziesz pełne obciążenie i enter potem pojawi się Mid kładziesz jeszcze raz 1/3 pełnego obciążenia i enter END powodzenia P.S. w załączniku serwisówka po angielsku
7
2
CONTENTS
PRECAUTIONS ............................................... 4
PREFACE........................................................... 5
NAMES AND FUNCTIONS ........................... 6
INSTALLATION & CONNECTION ........... 7
CALIBRATION ................................................ 8
OPERATIONS................................................. 15
1. General Weighing ........................................ 18
2. Weighing with Tare ....................................... 18
3. Counting Mode ............................................ 19
4. Percent Weighing Mode ................................ 20
5. Hold Function(Weight Mode ONLY) ............. 21
6. Cumulative Weight Sum ............................... 21
7. Weight Comparison Function(HI/OK/LOW) . 23
8. Print Out ..................................................... 26
9. Battery Charge............................................. 29
10. Unit conversion(Kg, lb, oz, g) ....................... 29
SETUP MODE................................................. 30
1. How to Go to Setup Mode............................. 30
2. Setup Mode Table ......................................... 30
3.TIME Setup Mode ........................................ 32
4. How to Enter Date ........................................ 33
5. How to Enter Time ....................................... 34
6. How to Enter Label Caption.......................... 35
ERROR MESSAGES ..................................... 36
SERIAL INTERFACE ................................... 36
SPECIFICATIONS......................................... 37
ASSEMBLING THE DISPLAY OF DB-II
WALL TYPE .................................................... 39
3
PRECAUTIONS
4
PREFACE
Thank you for the purchasing of CAS DBI(LCD) / DDI Indicator.
This series have been designed with CAS reliability, under rigid quality control
and with outstanding performance. Your specialty departments can enjoy with
CAS products.
We hope that CAS product meets your needs.
The user manual is designed to guide you to understand product operation and
proper care of product.
5
NAMES AND FUNCTIONS
OVERALL VIEW
DBI(LCD/LED)
DDI
* DBI (LED
* DBI (LCD) / DDI
=
=
FOR DBI (LED) Version.
FOR DBI ( LCD) & DDI Version.
6
INSTALLATION & CONNECTION
Load cell connection
Connect load cell connector to load cell port which is in the backside of the indicator.
* Connecting method
IN
COLOR
1 (EXC+)
RED
2 (EXC-)
WHITE
3 (SIG+)
GREEN
4 (SIG-)
BLUE
5 (SHIELD)
SHIELD
Note. Wire color can be different depending on the
loadcell’s manufacturer or it’s model.
* Load cell output to Resolution
5V impression to loadcell
Max. load cell output
Recommended resolution
4 mV
1/4,000
8 mV
1/8,000
10 mV
1/10,000
7
CALIBRATION
General Calibration
Pressing and holding calibration switch press [POWER] key to go to calibration mode.
User can move to other mode by using [HOLD],[PRINT] key in the calibration mode.
Please simply follow below procedure to move to other mode.
User also moves to other sub-modes for each mode by using [TARE] key. _* DBI (LED)
● Calibration Mode: Pressing and holding “Calibration Switch” press [POWER] key.
● It displays “CAL 1” after “onE”.
● Selecting menu: press [HOLD],[PRINT]
● ENTER(Setting) : [SAMPLE] key
MODE
Function
CAL 1
Display normalized AD
CAL 2
Display Keypad infomation-
CAL 3
[SAMPLE] → “Zero” → Weight Setting Mode (Zero Weight)
[SAMPLE] → “MID” → [SAMPLE] after loading for 1/3 weight →
[SAMPLE] → “FULL” → [SAMPLE] after loading for Full weight →
[SAMPLE] → “MID” → [SAMPLE] after loading for 1/3 weight → “END”
CAL 4
Option Setting ( Table 1 )
CAL 5
Display filtered Raw AD
CAL 6
N/A
CAL 7
% Calibration
CAL 8
Battery calibration
Gravity constant
CAL 9
CAL 10
Set calibration factor
“Unit” [SAMPLE] select 0, 1 (0:kg, 1: lb) [SAMPLE]
“CAPA” [SAMPLE] select capacity [SAMPLE]
“MID” [SAMPLE] select mid-capacity [SAMPLE]
“W-dP” [SAMPLE] Select Decimal Point [SAMPLE]
“ 1 d ” [SAMPLE] Select division [SAMPLE]
“Dual” [SAMPLE] Enable dual interval (0:disable, 1:enable)
“tare” [SAMPLE] Enable custom tare (0:disable, 1:enable) [TARE]
Set nation( 99: Default)
CAL 11
8
& lt; Modes & gt;
C4 Setting
When you entered CAL-4, the scale will display 8 Bits Hexadecimal value in the “Total Price Display
panel. For example, B0(16) presents 10110000(2). In C41 setting, it sets (+/-)10% zero range, last digit
invalid enable, (+/-)2% key zero percent, proper successive tare type, gross zero indication. Please refer
to below table.
Bit
7(MSB)
6
5
4
3
2
1
0(LSB)
Value
1
0
1
1
0
0
0
0
C4-1 Setting (AD)
Bit
Set (1)
Clear (0)
Remark
00 : ±2%
7, 6
01 : ±3%
Initial Zero Range
10 : ±10%
11 : ±5%
5
Last Digit Invalid Enable
Last Digit Invalid Disable
Same as 4-4 3rd bit
4
±2% Key zero percent
±3% Key zero percent
For Sri Lanka
00 : Proper
3, 2
01 : Positive Direction
Successive Tare Type
10 : Negative Direction
11 : All Direction
00 : Gross zero indication
1, 0
Zero mark type
01 : Net zero indication
10 : Both zero indication
9
C4-3 Setting (Sale) _* DBI (LCD) / DDI
Bit
Set (1)
Clear (0)
7
Dot type Comma
Dot type Dot
6
Use Preset Tare
Don't Use Preset Tare
5
Use Backlight
Don't Use Backlight
4
Use Head Message
Don't Use Head Message
3
Use Gram Unit
Don't Use Gram Unit
2
Use Ounce Unit
Don't Use Ounce Unit
1
Use Pound Unit
Don't Use Pound Unit
0
Use Kilo Gram Unit
Don't Use Kilo Gram Unit
* Even if C4-3 is set to 5F the unit change will not able to use because of Max capa setting
And you must choose only two weight unit.
10
Remark
SPAN Calibration Setting (C-3)
(1)Pressing and holding “Calibration Switch” press [POWER] key.
It displays “CAL 1” message.
(2)Press [
] to display “CAL-3”.
(3)Press [
] key and then it displays “zero ” message.
(4)Press [
] key and then it displays “midup” message
● Load middle weight (ex:”C-10” “MID” set Weight) on the platform
●Press [
] key and then it displays “span ” message
●Load full weight on the platform
●Press [
] key and then it displays “middn” message
●Load middle weight (ex:”C-10” “MID” set Weight) on the platform
●Press [
] key and then it display “CAL 3” message
●Weight Calibration is normally finished.
●Press [
] key two times and then you can go to Weight mode.
Gravity Constant Value Setting (C-9)
Current gravitational Acceleration value is set to 9.7994 m/s2 .
(1)Pressing and holding “Calibration Switch” press [POWER] key.
It displays “CAL-1” message.
(2) Press [
] to display “C-9”.
(3) Press [
] key, and then “ G-1“ message and “9.7994” will be shown. The first digit,”9” will blink.
(4)Input a gravitational acceleration value by using [
(5)Press [
blink.
key.
] key, and then “G-2” message blinks. “9.7994” will be shown. The first digit,”9” will
(6) Input a gravitational acceleration value by using [
(7) Press [
]
] key.
] key to save the gravitational acceleration value, and “C-9” message will be shown.
.
11
Calibration factor Setting (C-10)
(1)Pressing and holding “Calibration Switch” press [
] key.
(2)It displays “CAL-1” message.
(3)Press [
] to display “C-10”.
(4)Press [
] key, and then “UNIT” message and “0” will be shown. The first digit,”0”
will blink. It means calibration unit is “kg” (0 : kg, 1 : lb)
(5)Input a calibration unit by using [
(6)Press [
] key.
] key, and then “CAPA” message blinks. “0015” will be shown. The first digit,”0”
will blink. It means a full-capability is “15 (calibration unit, kg or lb)”
(7)Input a capability by using [
(8)Press [
] key.
] key, and then “MCAPA” message blinks. “0005” will be shown. The first digit,”0”
will blink. It means a mid-capability is “05 (calibration unit, kg or lb)”
(9)Input a capability by using [
(10)Press [
] key.
] key, and then “W-예” message blinks.“3” will be shown. The first digit, “3” will
blink. It means a weight decimal point is “3 (will display 0.000)”
(11)Input a weight decimal point by using [
(12) Press [
] key.
] key, and then “1d “”message blinks.“0.005” will be shown. The third digit,”0”
will blink. It means a division is “0.005 (calibration unit, kg or lb)”
(13) Input a division by using [
(14) Press [
] key.
] key, and then “dual” message blinks.“1” will be shown. The third digit, “1” will
blink. It means a dual interval is disable. “(0 : disable, 1 : enable)”
(15) Input a dual interval enable by using [
(16) Press [
] key.
] key, and then “tare” message and “0” will be shown. You can enable or disable
custom tare (0:disable, 1:enable)
(17) Press [
] key to save the calibration factor, and “C-10” message will be shown.
12
Displaying Real A/D Value (C-5)
Display Raw AD
Percent Calibration (C-7)
(1) Pressing and holding “Calibration Switch” press [POWER] key.
It displays “CAL 1” message.
(2) Press [
] to display “CAL-7”.
(3) Press [
] key and then it displays “Per 10” message. Select the percent value using the
[
] key. You can choose 10, 20, 30, 40, 50, 60, 70, 80, 90 percent.
(4) Press [
] key and then it displays “zero” message
(5) Press [
] key and then it displays “pspan” message
(6) Load choice percentage weight of full weight on the platform
(7) Press [
] key and then it displays “CAL 7” message
(8) Press [
] key two times and then you can go to Weight mode.
Battery Calibration (C-8)
- Engineer MODE
Calibration factor Setting (C-10)
MAXIMUM CAPACITY SETTING TABLE
kg
lb
oz
gram
1
2
X
1000
2
5
80
2000
3
6
X
3000
5
10
160
5000
6
15
X
6000
10
20
400
10000
12
25
X
12000
13
15
30
X
15000
20
50
800
20000
25
50
X
25000
30
60
1000
30000
50
100
X
50000
60
150
X
60000
100
200
X
X
150
300
X
X
200
500
X
X
300
600
X
X
500
1000
X
X
600
1500
X
X
1000
2000
X
X
2000
5000
X
X
3000
6000
X
X
5000
10000
X
X
10000
20000
X
X
15000
30000
X
X
20000
50000
X
X
30000
60000
X
X
50000
X
X
X
60000
X
X
X
14
OPERATIONS
DISPLAY AND KEYBOARD
DBI(LED)
STATE SIGNAL ( DBI LED) _* DBI (LED)
STATE
STABLE
DESCRIPTIONS
Weight measurement state is stable.
▶ ◀
●
Current weight is “0” kg
NET
ON(net weight), OFF(gross weight)
SUM
Summation of the Each Weight
LOW
Battery Low Signal
POWER
ADAPTER Power ON Signal
15
DBI(LCD)
DDI
16
KEY FUNCTIONS
KEYS
DESCRIPTIONS
Used to set the zero point to 0.00.
Used as an ESC key in Setup Mode.
Used to enter a tare weight and used to cancel a tare weight.
Used to convert the mode as below.
[kg] [pcs] [%] [WEIGHT LIMIT ON/OFF]
[COUNT LIMIT ON/OFF] [kg]
Used as an ENTER key.
Used to calculate a unit weight of a sample..
[▶] Used to enter next digit.
Used to display average weight.
[
] Used to have number up.
PRINT key.
[▼] Used to have number down.
Used to turn ON or OFF the power.
17
1. General Weighing
■ The display indicates if the scale is at zero or if there is a tare entered into the
scale by way of a ZERO and NET.
① Turn on the power.
The display shows 0.00.
Make sure that STABLE and
ZERO lamps are on.
② When the display is not zero
though there is nothing on
the platter, press the ZERO
key.
③ Place an item on the platter.
When the STABLE lamp is
on, read the weight.
2. Weighing with Tare
■ Tare is the weight of container being used for a commodity.
The TARE key subtracts the weight of the container.
① Place the container on the
platter.
② Press the TARE key, NET
lamp is on.
③ Place an item in the
container.
④ To release the TARE function, remove an item and
container from the platter and press the TARE key.
18
3. Counting Mode _* DBI (LCD) / DDI
■ If you want to count parts, first you have to set sample size.
OR
① Press the MODE key until the display shows “PCSSET”. Make
sure that PCS lamp is on. If you have set sample size before,
the display shows “0”.
② Press the SAMPLE key,
then the display shows “10”.
③ If you want to increase sample size, press the SAMPLE key.
The display shows 10, 20, 30, 40, 50, 100, 150 and 200 every
time pressing the SAMPLE key.
④ If you set sample size to 10, place 10 samples on the platter.
⑤ Press the SET key. The display shows unit weight and then shows the number of samples. If the
display shows “LACK”, the counting result may not correct. (LCD version : Lack of Unit lamp is On) If
the display shows “ Low ”, it is impossible to count samples because the unit weight is too small. (Refer to Table 1)
(Example)
15kg
30kg
60kg
150kg
300kg
Range of Lack (Single)
MaxCapacity
2g ≥Lack ≥0.1g
6kg
5g ≥Lack ≥ 0.1g
10g≥Lack ≥0.1g
20g ≥Lack ≥1g
50g ≥Lack ≥1g
100g ≥Lack≥1g
Range of Lack (Dual)
1g ≥Lack ≥0.1g
2g ≥Lack ≥ 0.1g
5g ≥Lack≥ 0.1g
10g ≥Lack ≥1g
20g ≥Lack ≥1g
50g ≥Lack ≥1g
Range of Low
0.1g ≥Low
0.1g ≥ Low
0.1g≥ Low
1g ≥Low
1g ≥Low
1g ≥Low
& lt; Table 1 & gt;
19
* The small value that can escape from ‘LACK’ message is over MAX CAPA / 3000.
⑥ Place parts on the platter, then the display shows the number
of parts. You can also use tare function in counting mode.
4. Percent Weighing Mode _* DBI (LCD) / DDI
■ The weight is displayed as a percentage of the reference.
OR
① Press the MODE key until the display shows “PErSEt”. If you
have set reference sample before, the display shows “0.0”.
②If you want to use container,
place it and press the TARE key.
③ Place reference sample on the platter and press the SAMPLE
key.
The display shows “100.0”.
Make sure that reference sample should be bigger than 3% of
maximum capacity. If it is lower than 3% of maximum capacity,
the display shows “Low”. In this case, increase the weight of
reference sample and press the SAMPLE key.
④ Place an item on the platter, then the weight is displayed as a
percentage of the reference.
20
5. Hold Function(Weight Mode ONLY) _* DBI (LCD) / DDI
① Place an item on the platter and then press the HOLD key.
① “HOLD” is shown on the
display.
② Average weight is shown on
the display.
■ To release HOLD function, press the HOLD key or remove the item from the platter.
6. Cumulative Weight Sum
The function of cumulative weight sum is to be showing the aggregate times and
weight as adding the value of weighing a several times. Even though power is
off, the scale stores data. This function is only available in weighing mode.
① Place an item on the platter.
② To add this weight, press the SAMPLE key. Make sure that
SUM lamp is on.
③ The display shows cumulative weight sum and aggregate times every time pressing the SET key.
The SUM key is flashed.
21
④ To cancel last added weight, press the SET key to display cumulative weight sum or aggregate
times and then press the SAMPLE key. The display shows “S SUB”.
⑤ You can delete cumulative weight sum or aggregate times. Press the SET key to display
cumulative weight sum or aggregate times and then press the ZERO(ESC key).
⑥ To print out cumulative weight sum, press the SET key to display cumulative weight sum or
aggregate times and then press the PRINT key.
22
7. Weight Comparison Function(HI/OK/LOW) _* DBI (LCD) / DDI
7-1. How to compare weight
① Press the MODE key until
the display shows “WL OFF”.
It means that weight limit
function is deactivated.
② Press the HOLD key to
activate this function, the
display shows “WL ON”.
③ Press the SET key to set up
low value, the display shows
“L000.00”.
④ Press the HOLD(▲) or
PRINT(▼) key to have
number up or down. To enter
next digit, press the SAMPLE
key.
⑤ Press the SET key to set up
high value, the display
shows “H000.00”.
⑥ Press the HOLD(▲) or
PRINT(▼) key to have
number up or down. To enter
next digit, press the
SAMPLE(▶) key.
⑦ Press the SET key, the
display shows “WL ON”.
⑧ If you set up LOW/HIGH limit wrong, “WL ERR” will be shown on the display. Then you have to set it
up again. For example) LOW=100.00kg HIGH=90.00kg High limit is lower than Low limit.
⑨ Press the MODE key to go to weighing mode.
⑩ Suppose that the High limit of 70kg and the Low limit of 30kg are set up. In this condition, OK lamp is
lighted on if the weight is 40kg, HI lamp is lighted on if the weight is 80kg and if the weight is 20kg,
LO lamp is lighted on. It beeps as fixed on User Setup Mode.
23
(Refer to Setup Mode Table on page 30)
7-2. Counting comparison function
① Press the MODE key until
the display shows “CL OFF”.
It means the counting
comparison function is
deactivated.
② Press the HOLD(▲) key to
activate this function, the
display shows “CL ON”.
③ Press the SET key, the
display shows “L00000”.
④ Press the HOLD(▲) or
PRINT(▼) key to have
number up or down. To enter
next digit, press the
SAMPLE(▶) key.
⑤ Press the SET key, the
display shows “H00000”.
⑥ Press the HOLD(▲) or
PRINT(▼) key to have
number up or down. To enter
next digit, press the
SAMPLE(▶) key.
24
⑦ Press the SET key, the
display shows “CL ON”.
⑧ If you set up LOW/HIGH limit wrong, “CL Err” will be shown on the display. Then you have to set it
up again. For example) LOW=00100, HIGH=00090 or LOW=00100, HIGH=00100
⑨ Press the MODE key to go to counting mode.
⑩ Suppose that the High limit of 200 and the Low limit of 80 are set up. In this condition, OK lamp is
lighted on if the weight is 120, HI lamp is lighted on if the weight is 220 and if the weight is 60,
LO lamp is lighted on. It beeps as fixed on User Setup Mode.
(Refer to Setup Mode Table on page 17)
25
8. Print Out
8-1. Manual Print
* DBI (LCD) / DDI
■ You can print out data every time pressing the PRINT key. You can setup
print function depends on your need. Refer to Setup Mode Table on page 30.
Sample format(DEP-50):
-Weighing Function-
-Counting Function-
======== WEIGHT ========
WELCOME TO CAS
DATE . 07/30/2007
TIME. 17:35:58
======== COUNT ========
WELCOME TO CAS
DATE. 07/30/2007
TIME. 17:35:58
Weight :
0.000 kg
Weight :
Quantity :
- WEIGHT LIMIT SET VALUE Limit(H):
40.000 kg
Limit(L):
30.000 kg
40.200 kg
50 pcs
- COUNT LIMIT SET VALUE Limit(H):
2000 pcs
Limit(L):
1000 pcs
When ‘the weight comparison function’is set.
When ‘the counting comparison function’is set.
-Cumulative Weight Sum Function(DEP only)
======== WEIGHT ========
WELCOME TO CAS[DB-2]
DATE . 07/30/2007
TIME. 17:35:58
Label Caption
Date
Time
Weight :
40.180 kg
Weight :
40.200 kg
Weight :
40.200 kg
Weight :
40.200 kg
Weight :
40.200 kg
Weight :
40.200 kg
Weight :
40.200 kg
Weight :
40.200 kg
Weight :
- 40.200 kg
Weight :
40.200 kg
Weight :
40.200 kg
Weight :
40.200 kg
-------------------------Total :
401.980 kg
Count :
10 times
- means that you cancel the weight right before
this weight.
Cumulative weight sum
Aggregate times
※ Please take a reference of page 11(cumulative weight sum) for printing process details.
Sample format(DEP-50):
26
Notice. 4 kinds of Print forms should downloaded to the DLP Printer to use all the features and
Function smoothly
1. Weight + tare
※ In order to use the above label format, Barcode
set as OFF and weight comparison function as
OFF in SETUP MODE
2. Weight + Tare + Barcode
※ In order to use the above label format, Barcode
set as ON and weight comparison function as
OFF in SETUP MODE
3. counting function
※ Quantity Comparison Functions should set as ON
4. Weight comparison function
※ Weight comparison functions should set as ON
※ When using DLP printer, it could not print in the percentage mode
27
* DBI (LED)
-Weighing Function======== WEIGHT ========
DATE . 07/30/2007
TIME. 17:35:58
Weight :
0.000 kg
-Cumulative Weight Sum Function======== WEIGHT ========
DATE . 07/30/2007
TIME. 17:35:58
Label Caption
Date/Time
Weight :
40.180 kg
Weight :
40.200 kg
Weight :
40.200 kg
Weight :
40.200 kg
Weight :
40.200 kg
Weight :
40.200 kg
Weight :
40.200 kg
Weight :
40.200 kg
Weight :
- 40.200 kg
Weight :
40.200 kg
Weight :
40.200 kg
Weight :
40.200 kg
-------------------------Total :
401.980 kg
Count :
10 times
- means that you cancel the weight right before
this weight.
Cumulative weight sum (SAMPLE KEY)
( After each weight sum, it use PRINT KEY
.)
Aggregate times
8-2. Auto Print
① To use auto print function, you have to set printer menu to “Pr AUt” in setup mode.
Refer to Setup Mode Table on page 30.
② If the weight is stable, it is printed out automatically.
And You can print out data every time pressing the PRINT key.
* DBI (LCD )/DDI
① To use auto print function, you have to set printer menu to “Pr Str” in setup mode.
Refer to Setup Mode Table on page 30.
8-3. Stream Print
② If the weight is stable, it is printed out continuously
28
9. Battery Charge
* DBI (LCD) / DDI
■ Warning massage is shown when the battery voltage is very low. (
)
* DBI (LED)
■ Warning massage is shown when the battery voltage is very low. (
)
■ At this time, charge the battery. (a charging battery only)
■ The display will show a red lamp and the battery will begin a fast charge
automatically.
- Use only the ac adapter which comes with the scale. Other AC adapter may
cause damege.
10. Unit conversion (Kg, lb, oz, g) _* DBI (LCD) / DDI
① Press 5 on MODE
key at weighing mode.
The display shows “U kg”.
(or your last unit)
② Use “HOLD key” or
“PRINT key” you can set which
unit you want to use.Kg, lb, oz.
③ Press “SET key” and
“CHAnGE” will display.
④ Press the “MODE” key to go
to the weighing mode.
※ Tare, Unstable, when the display weight is not when change is not working.
Leave the platter empty, and weighing is at Zero and stable, the scale should work.
29
SETUP MODE
1. How to Go to Setup Mode
Make sure that power is OFF. While pressing the PRINT key, press the POWER key. The display
shows “U SEt”. You can select each menu by pressing the MODE key and change the setting by
pressing the HOLD or PRINT key. If you press SET key, you will save current setting and finish this
mode. To finish this mode without saving, press the ZERO key.
2. Setup Mode Table
MENU
DISPLAY
“ b on ”
Buzzer
“ b oFF ”
DESCRIPTIONS
You can hear buzzer.
You cannot hear buzzer.
“Pr oFF”
Do not use printer.
“Pr DLP”
DLP50 printer interface. (Label)
“Pr DEP”
Printer
DEP50 printer interface. (Ticket)
*DBI
(LCD)
*DDI
“Pr key”
Manual print. (DLP DEP)
,
Linefeed
(DEPonly)
Barcode
(DLP only)
DBI
(LED)
Manual print.
“P AUt”
*DBI
(LCD)
*DDI
Ptint continually when the scale is stable. (DEP)
“P kEy”
DBI
(LED)
Auto print when the scale is stable. (DLP DEP)
,
“Pr Str”
Auto print when the scale is stable.
“P Str”
Print
method
“Pr AUt”
Stream print when the scale is stable.
LF1~LF9
Linefeed
“LF 1”
1 line feed
“LF 9”
9 line feed
“BC on/off”
Print out barcode on/off.
“br 48”
Baud Rate
4,800 bps _* DBI (LCD) / DDI
“ br 96 ”
9,600 bps
“ br 192 ”
19,200 bps
“ br 384 ”
38,400 bps
“ bL on ”
Backlight
*DBI (LCD)
*DDI
Use back-light.
“ bL 10 ”
Back-light is on 10 seconds.
“ bL 30 ”
Back-light is on 30 seconds.
“ bL oFF ”
Brightness
*DBI (LCD)
*DDI
“ 1 ~7 ”
Do not use back-light.
You can set backlight brightness. (Default : 3)
30
“ AP oFF ”
Auto Power
Off
“ AP 10 ”
“ AP 30 ”
“ AP 60 ”
“ WL M0 ”
Weight
Limit
*DBI (LCD)
*DDI
Do not use Auto Power Off function.
Power turns to be off automatically when the scale is
not in operation over for 10 minutes.
Power turns to be off automatically when the scale is
not in operation over for 30 minutes.
Power turns to be off automatically when the scale is
not in operation over for 60 minutes.
HIGH Limit ≥ Weight ≥ LOW Limit - You will hear
buzzer.
HIGH Limit ≤ Weight, Weight ≤ LOW Limit
- You will hear buzzer.
“ WL M2 ”
Weight ≤ LOW Limit - You will hear buzzer.
“ WL M3 ”
HIGH Limit ≤ Weight - You will hear buzzer.
“ CL M0 ”
HIGH Limit ≥ Counting result ≥ LOW Limit
- You will hear buzzer.
“ CL M1 ”
HIGH Limit ≤ Counting result,
Counting result ≤ LOW Limit - You will hear buzzer.
“ CL M2 ”
Count Limit
*DBI (LCD)
*DDI
“ WL M1 ”
Counting result ≤ LOW Limit - You will hear buzzer.
“ CL M3 ”
Date
*DBI(LCD)
*DDI
Time
*DBI (LCD)
*DDI
HIGH Limit ≤ Counting result - You will hear buzzer.
“ dy on ”
Print out date/day.
“ dy oFF ”
“ ti on ”
Do not print out date/day.
Print out time.
Suspend
Mode
*DBI (LED)
Default
Do not print out time.
“ LA off ”
Do not print out label caption.
“ LA on ”
Label
“ ti oFF ”
Print out label caption.
“SUS00”
“SUS20”
“SUS40”
“ SUS60 ”
“ dF no ”
“ dF YES ”
Do not use Sleep Mode.
Suspend mode is activated after 20 seconds.
Suspend mode is activated after 40 seconds.
Suspend mode is activated after 60 seconds.
Default setting is released.
Everything is setup in default.
※ Italic Bold : Default Setting
※Select the DEP printer in the Set up mode, LINE Feed Features are enable to use and if DLP printer is
selected then Barcode features are enable to use. However, both Line Feed and Barcode features
could not use at the same time.
31
3. TIME Setup Mode _* DBI (LED)
While pressing the ZERO key, press the POWER key.
The Next Display is “ tiME” .
(1) Year Setting Mode
“tiME” - & gt; SET Key - & gt; “ YAr00” - & gt; Change the setting by pressing the HOLD or PRINT key.
If you press SET key, you will save current setting. Next Mode is Month Setting Mode.
(2) Month Setting Mode
“ MtH00” - & gt; Change the setting by pressing the HOLD or PRINT key.
If you press SET key, you will save current setting. Next Mode is Day Setting Mode.
(3) Day Setting Mode
“ dAy00” - & gt; Change the setting by pressing the HOLD or PRINT key.
If you press SET key, you will save current setting. Next Mode is Hour Setting Mode.
(4) Hour Setting Mode
“ Hor00” - & gt; Change the setting by pressing the HOLD or PRINT key.
If you press SET key, you will save current setting. Next Mode is Minute Setting Mode.
(5) Minute Setting Mode
“ Min00” - & gt; Change the setting by pressing the HOLD or PRINT key.
If you press SET key, you will save current setting. Next Mode is Second Setting Mode.
(6) Second Setting Mode
“ SEC00” - & gt; Change the setting by pressing the HOLD or PRINT key.
If you press SET key, you will save current setting and finish this mode.
32
4. How to Enter Date _* DBI (LCD) / DDI
① Press the MODE key until
the display shows “dy ON”. It
means that date is printed out.
② If you do not want to print out date, press the HOLD(▲) key.
③ Press the SAMPLE(▶) key,
the display shows
“00,00,00”.
④ Press the HOLD(▲) or
PRINT(▼) key to have
number up or down. To enter
next digit, press the
SAMPLE(▶) key.
⑤ Press the SET key to save.
“dysave” is shown on the
display and then the display
shows a day of the week.
⑥ You can change the day by
pressing the HOLD(▲) or
PRINT(▼) key. If you set up
a day of the week wrong,
“Wk err” is shown on the display.
⑦Press the SET key to save.
“Wksave” is shown on the
display.
⑧You can change the date by
pressing the HOLD(▲) or
PRINT(▼) key.
33
Press the SET key to save.
If you do not want to save,
“dtsave” is shown on the
display.
press the ZERO key.
5. How to Enter Time _* DBI (LCD) / DDI
① Press the MODE key until the
display shows “ti ON”. It
means that time is printed out.
②If you do not want to print out time, press the HOLD(▲) key.
③ Press the SAMPLE(▶) key
to set up time, “00,00,00”
is shown on the display.
④ Press the HOLD(▲) or
PRINT(▼) key to have
number up or down. To enter
next digit, press the
SAMPLE(▶) key.
⑥ If you do not want to save time, press the ZERO key.
34
⑤ Press the SET key to save.
“tisave” is shown on the
display.
6 . How to Enter Label Caption
/ aximum 24characters _* DBI (LED) /
① Press the MODE key until
the display shows “LA off”.
It means that label caption
is not printed out.
②To print out label caption, press the HOLD (▲) key.
The display shows “LA on”.
③ Press the SAMPLE(▶) key,
“WELCOM” is shown on the
display in default.
④ You can program label caption by pressing HOLD(▲) or
PRINT(▼) key. To enter next digit or previous digit, press
the MODE or SAMPLE(▶) key.
⑤ You can enter alphabet or special character by pressing the TARE key. When you enter special
character, STABLE lamp is on. When you enter alphabet, STABLE lamp is off.
⑥ Press the SET key to save. “LA save” is shown on the display.
⑦ If you do not want to save, press the ZERO key.
35
ERROR MESSAGES
Error
Message
on Display
Description
Solution
“Err 0”
The " Err 0 " occurs when scale is not stable.
Remove unstable facts.
“Err 1”
The " Err 1 " occurs when a current zero point
has shifted from the last span calibration.
Please call your CAS dealer.
“Err 3”
The " Err 3 " is an overload error.
Please remove the weight.
“Err 9
“Err 14”
The " Err 9 " is no weight error. When scale is
in counting mode, you must load the weight.
If you have no weight on your scale, you can
see this error message.
The " Err 14 " means calibration range is not
correct.
SERIAL INTERFACE
36
Please load the weight on your tray.
Please call your CAS dealer.
SPECIFICATIONS _* DBI (LCD) / DDI
Load Cell Excitation
Voltage
Zero Adjustment
Range
DC 5V
0.05mV ~ 5mV
Input Sensitivity
2uV/D
A/D
Internal Resolution
A/D
External Resolution
1/60000
1/3000
Division
X1, x2, x5
A/D
Conversion Speed
8 Hz
Display Below Zero
Minus
DISPLAY
DISPLAY LAMP
LCD 6 digits 10mm(W) X 22mm(H)
STABLE, ZERO, HOLD, NET, HI/OK/LO, lb, oz
%, PCS, SUM, kg, Low Battery
INTERFACE
RS-232C(Printer)
DBI
POWER SOURCE
TEMPERATURE
RANGE
PRODUCT SIZE
(WDH)mm
-10°C ~ +40°C
DBI
DDI
220(W)X174(D)X240(H)
220(W)X159(D)X107(H)
PRODUCT
WEIGHT
MINIMUM
VOLTAGE LEVEL
OF THE BATTERY
CONTINUOUS
USING TIME
DDI
DC 12V 1.25A Adaptor
6V 4Ah Pb Battery, Dry Battery
AA Size X 4
DC 12V 1.25A Adaptor
6V 3.3Ah Pb Battery, Dry Battery
1.5kg
About 5.6V
DBI
About 100 Hours
(Back light Off)
About 25 Hours
(Back Light On / Brig7 / 100mA)
*The load Cell Specification
can have a effect on using
time.
RECHARGING
DDI
About 150 Hours
(Back light Off / 20mA)
About 14 Hours
(Back Light On / Brig7 / 250mA)
*The load Cell Specification
can have a effect on using
time.
About 12 Hours
▶Notice: Specifications are subject to change for improvement without notice.
37
SPECIFICATIONS _* DBI (LED)
Load Cell Excitation
Voltage
DC 5V
Zero Adjustment Range
0.05mV ~ 5mV
Input Sensitivity
2uV/D
A/D Internal Resolution
1/60000
A/D External Resolution
1/3000
Division
X1, x2, x5
A/D Conversion Speed
8 Hz
Display Below Zero
Minus
DISPLAY
DISPLAY LED LAMP
LED 5 digits
STABLE, ZERO, NET, SUM,LOW, POWER LED
INTERFACE
RS-232C(Printer)
DC 12V 1.25A Adaptor
6V 3.6AH Pb Battery
POWER SOURCE
TEMPERATURE
RANGE
MINIMUM VOLTAGE
LEVEL OF THE
BATTERY
-10°C ~ +40°C
About 5.6V
WEIGHT
About 1.5kg kg
Rechargeable Time
12 Hour
Consumption Current
About 50 mA
Battery Consumption
Time
PRODUCT SIZE
(W D H)mm
50 Hour
220 x 177 x 87
▶Notice: Specifications are subject to change for improvement without notice.
38
ASSEMBLING THE DISPLAY OF DB-II WALL TYPE
1. Attach head bracket to the display and fasten it with screws provided asshown in Figure. 1.
2. Connect both of grand wire and load cell wire to load cell connector at thebackside of display as
shown in Figure. 2.
3. Fasten grand wire to the bottom of platform body with bolt as shown in Figure. 3.
39
40
뒷표지
41