Pewnie MC80F0708G (zał. masz datasheet) * w Chinach ok. 2-3.$ Jak uszkodzona szukaj nowego zasilacza lub coś "zblizonego" dla plasm 50" LG np. EAY39190301 ( z dodaniem czasem zasilacza stby +5V) PSPU-J903A EAY60696901... jest w plasmach 42" LG 42PQ100 (ma ten IC MC80F...) PSPU-J904A EAY60704401 * PSPU-J905A EAY60704701 - ten sam pcb https://obrazki.elektroda.pl/2226854400_1504020580_thumb.jpghttps://obrazki.elektroda.pl/2724859700_1504020605_thumb.jpg p.s EAY60696801 (PSPU-J902A) PSPU-J902A(903A), na : L6599D ,2A20112, MC80F0708G IC701: MC80F0708G *wer. firmware LGIT PSU V1.01C A387 Czytaj Link Lub z tego forum min. Link_ np.
www.DataSheet.in
ABOV SEMICONDUCTOR
8-BIT SINGLE-CHIP MICROCONTROLLERS
MC80F0704/0708
MC80F0804/0808
User’s Manual (Ver. 1.02)
Version 1.02
Published by
FAE Team
©2006 ABOV semiconductor Co., Ltd. All right reserved.
Additional information of this manual may be served by ABOV semiconductor offices in Korea or Distributors and Representatives.
ABOV semiconductor reserves the right to make changes to any information here in at any time without notice.
The information, diagrams and other data in this manual are correct and reliable; however, ABOV semiconductor is in no
way responsible for any violations of patents or other rights of the third party generated by the use of this manual.
www.DataSheet.in
MC80F0704/0708/0804/0808
REVISION HISTORY
VERSION 1.02 (August 18, 2009) This Book
Rearranged device order and fixed some errata.
The figures of flash writer were updated in " 1. OVERVIEW " on page 1.
Config Read Voltage(VCONFIG), maximum VDD Start Voltage(VSTART) and Figure 7-1 were added in " 7.4 DC Electrical
Characteristics " on page 16.
The recommended loadcapacitor values for main-oscillator circuit were added to 10pF~30pF in " 10. CLOCK GENERATOR " on page 42.
In case AVREF voltage was less than VDD voltage for ADC, the table-note and note were added in " 7.3 A/D Converter Characteristics " on page 15 and " 14. ANALOG TO DIGITAL CONVERTER " on page 69.
VERSION 1.01 (JUN 3, 2008)
Internal OSC specification was changed.
VERSION 1.0 (FEB 27, 2008)
Added AVREF parameter minimum voltage in " 7.3 A/D Converter Characteristics " on page 15.
Added charaeristics graphs in " 7.6 Typical Characteristics " on page 19.
VERSION 0.5 (SEP 28, 2007)
Fixed error in description and diagram of 8bit event counter.
VERSION 0.4 (MAY 5, 2007)
Added 2.2V ~ 5.5V @ 1 ~ 4MHz in " 7.2 Recommended Operating Conditions " on page 15.
Fixed error in Figure 9-2 on page 37 : changed R04, R07 and EC0,EC1 of PSR1 to R05, R06 and T0O, T2O
VERSION 0.3 (MAY 2, 2007)
Added 28 QFNP package in " 3. PIN ASSIGNMENT " on page 5.
VERSION 0.21 (MAR. 2007)
Changed 28 SOP package drawing in " 4. PACKAGE DRAWING " on page 6.
VERSION 0.2 (MAR. 2007)
Added TVDD parameter specification.
Note for configuration option was added and fix some errata.
VERSION 0.1 (AUG. 2006)
First Edition (Preliminary)
August 18, 2009 Ver 1.02
www.DataSheet.in
3
MC80F0704/0708/0804/0808
4
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
Table of Contents
2. BLOCK DIAGRAM .............................................4
8-bit Timer / Counter Mode ............................ 52
16-bit Timer / Counter Mode .......................... 57
8-bit Compare Output (16-bit) ........................ 58
8-bit Capture Mode ........................................ 58
16-bit Capture Mode ...................................... 63
PWM Mode .................................................... 65
3. PIN ASSIGNMENT .............................................5
14. ANALOG TO DIGITAL CONVERTER ........... 69
4. PACKAGE DRAWING ........................................6
15. SERIAL INPUT/OUTPUT (SIO) ..................... 72
Transmission/Receiving Timing ..................... 73
The usage of Serial I/O .................................. 75
1. OVERVIEW .........................................................1
Description ........................................................1
Features ............................................................1
Development Tools ...........................................2
Ordering Information .......................................3
5. PIN FUNCTION ...................................................9
6. PORT STRUCTURES .......................................11
7. ELECTRICAL CHARACTERISTICS ................15
Absolute Maximum Ratings ............................15
Recommended Operating Conditions .............15
A/D Converter Characteristics ........................15
DC Electrical Characteristics ..........................16
AC Characteristics ..........................................17
Typical Characteristics ....................................19
8. MEMORY ORGANIZATION .............................23
Registers .........................................................23
Program Memory ............................................26
Data Memory ..................................................28
Addressing Mode ............................................33
9. I/O PORTS ........................................................37
R0 and R0IO register ......................................37
R1 and R1IO register ......................................38
R2 and R2IO register ......................................40
R3 and R3IO register ......................................41
10. CLOCK GENERATOR ...................................42
Oscillation Circuit ...........................................42
11. BASIC INTERVAL TIMER ..............................44
12. WATCHDOG TIMER ......................................46
13. TIMER/EVENT COUNTER .............................49
August 18, 2009 Ver 1.02
www.DataSheet.in
16. BUZZER FUNCTION ..................................... 76
17. INTERRUPTS ................................................ 78
Interrupt Sequence ......................................... 81
BRK Interrupt ................................................. 82
Multi Interrupt ................................................. 82
External Interrupt ............................................ 84
18. POWER SAVING OPERATION ..................... 86
Sleep Mode .................................................... 86
Stop Mode ...................................................... 87
Stop Mode at Internal RC-Oscillated Watchdog
Timer Mode .................................................... 90
Minimizing Current Consumption ................... 92
19. RESET ........................................................... 94
20. POWER FAIL PROCESSOR ......................... 96
21. COUNTERMEASURE OF NOISE ................. 98
Oscillation Noise Protector ............................. 98
Oscillation Fail Processor ............................... 99
22. Device Configuration Area ........................ 100
23. Emulator EVA. Board Setting .................. 101
A. INSTRUCTION .................................................. ii
Terminology List .................................................ii
Instruction Map .................................................. iii
Instruction Set ...................................................iv
1
MC80F0704/0708/0804/0808
2
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
MC80F0704/0708
MC80F0804/0808
CMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
WITH 10-BIT A/D CONVERTER
1. OVERVIEW
1.1 Description
The MC80F0704/0708/0804/0808 is advanced CMOS 8-bit microcontroller with 4K/8K bytes of FLASH(MTP). This is a powerful microcontroller which provides a highly flexible and cost effective solution to many embedded control applications. This provides the following features : 8K bytes of FLASH, 256 bytes of RAM, 8/16-bit timer/counter, watchdog timer, 10-bit A/D converter, 8-bit Serial Input/
Output, buzzer driving port, 10-bit PWM output and on-chip oscillator and clock circuitry. It also has ONP, noise filter, PFD for improving
noise immunity. In addition, the MC80F0704/0708/0804/0808 supports power saving modes to reduce power consumption.
This document explains the base MC80F0808, the other’s eliminated functions are same as below table.
Device Name
FLASH Size
RAM
ADC
I/O PORT
MC80F0704G/0708G
28 SKDIP
MC80F0704D/0708D
MC80F0704U/0708U
Package
26 port
4K/8K
MC80F0804K/0808K
MC80F0804D/0808D
256B
16 channel
28 SOP
28 QFN
30 port
32 SDIP
32 SOP
1.2 Features
• 8K/4K Bytes On-chip Code FLASH (MTP)
• FLASH Memory
- Endurance : 100 cycles
- Data retention time : 10 years
• 256 Bytes On-chip Data RAM
(Included stack memory)
• Minimum Instruction Execution Time:
- 333ns at 12MHz (NOP instruction)
• Programmable I/O pins
(LED direct driving can be a source and sink)
- MC80F0804/0808 : 29/30
- MC80F0704/0708 : 25/26
• One 8-bit Basic Interval Timer
• Four 8-bit Timer/counters
(or two 16-bit Timer/counter)
• One Watchdog timer
• One 8-bit Serial Communication Interface:
- One Serial Input/Output (SIO)
• Two 10-bit High Speed PWM Outputs
• 10-bit A/D converter : 16 channels
August 18, 2009 Ver 1.02
www.DataSheet.in
• One Buzzer Driving port
- 488Hz ~ 250kHz@4MHz
• Four External Interrupt input ports
• On-chip POR (Power on Reset)
• Twelve Interrupt sources
- External input : 4
- Timer : 6
- A/D Conversion : 1
- SIO : 1
• Built in Noise Immunity Circuit
- Noise filter
- PFD (Power fail detector)
- ONP (Oscillation Noise Protector)
• Power Down Mode
- Stop mode
- Sleep mode
- Internal RC-Oscillated watchdog timer mode
• Operating Voltage & Frequency
- 2.2V ~ 5.5V (at 1 ~ 4MHz)
- 2.7V ~ 5.5V (at 1 ~ 6MHz)
- 3.0V ~ 5.5V (at 1 ~ 8MHz)
- 4.5V ~ 5.5V (at 1 ~ 12MHz)
1
MC80F0704/0708/0804/0808
• Operating Temperature : -40°C ~ 85°C
• Oscillator Type
- Crystal
- Ceramic resonator
- External RC Oscillator (C can be omitted)
- Internal Oscillator (4MHz/2MHz)
• Package
- 28SKDIP, 28SOP, 28QFN, 32SKDIP, 32SDIP
- Available Pb free package
1.3 Development Tools
The MC80F0704/0708/0804/0808 is supported by a full-featured macro assembler, HMS800 C compiler, an in-circuit emulator CHOICE-Dr.TM and OTP/FLASH programmers. There are
two different type of programmers such as single type and gang
type. Macro assembler operates under the MS-Windows 95 and
upversioned Windows OS.
Please contact sales part of ABOV semiconductor.
Software
Hardware
(Emulator)
FLASH Writer
- MS-Windows based assembler
- MS-Windows based Debugger
- HMS800 C compiler
- CHOICE-Dr.
- CHOICE-Dr. EVA80C0x B/D
- PGM Plus USB (Single writer)
- Stand Alone GANG4 USB
(Gang writer)
- CHOICE - SIGMA II(Single writer)
Figure 1-1 PGM plus USB (Single Writer)
2
www.DataSheet.in
Figure 1-2 Choice-Dr. (Emulator, USB Interface)
Figure 1-3 Stand Alone Gang4 USB (Gang Writer)
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
1.4 Ordering Information
Device name
FLASH ROM
MC80F0704G
MC80F0704D
MC80F0704U
MC80F0804K
MC80F0804D
MC80F0708G
MC80F0708D
MC80F0708U
MC80F0808K
MC80F0808D
Pb free package:
The “P” Suffix will be added at the original part number.
August 18, 2009 Ver 1.02
www.DataSheet.in
4K bytes
8K bytes
RAM
Package
256 bytes
28SKDIP
28SOP
28QFN
32SDIP
32SOP
256 bytes
28SKDIP
28SOP
28QFN
32SDIP
32SOP
For example; MC80F0708G(Normal package), MC80F0708G P
(Pb free package)
3
MC80F0704/0708/0804/0808
2. BLOCK DIAGRAM
PSW
Accumulator
ALU
PC
Stack Pointer
Data
Memory
RESET
Program
Memory
System controller
8-bit Basic
Interval
Timer
System
Clock Controller
Timing generator
Data Table
Interrupt Controller
Clock Generator
Instruction
Decoder
Watch-dog
Timer
SIO
VDD
VSS
R3
10-bit
A/D
Converter
8-bit
Timer/
Counter
R0
High
Speed
PWM
Buzzer
Driver
R1
R2
Power
Supply
R31 / AN14
R32 / AN15
XIN / R33
XOUT / R34
4
www.DataSheet.in
R00 / INT3 / SCK
R01 / AN1 / SI
R02 / AN2 / SOUT
R03 / AN3 / INT2
R04 / AN4 / EC0
R05 / AN5 / T0O
R06 / AN6 / T2O
R07 / AN7 / EC1
R10 / AN0 / Avref / PWM1O
R11 / INT0 / PWM3O
R12 / INT1 / BUZO
R13
R14
R15
R16
R17 / AN8
R20
R21
R22
R23 / AN9
R24 / AN10
R25 / AN11
R26 / AN12
R27
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
3. PIN ASSIGNMENT
32SDIP/SOP
28 SKDIP/ SOP
3
30
R01 / AN1 / SI
R06 / AN6 / T2O
3
26
R01 / AN1 / SI
R07 / AN7 / EC1
4
29
R00 / INT3 / SCK
R07 / AN7 / EC1
4
25
R00 / INT3 / SCK
VDD
5
28
VSS
VDD
5
24
VSS
R10 / AN0 / AVREF / PWM1O
6
27
RESET / R35
R10 / AN0 / AVREF / PWM1O
6
23
RESET / R35
R11 / INT0 / PWM3O
7
26
XOUT / R34
R11 / INT0 / PWM3O
7
22
XOUT / R34
R12 / INT1 / BUZO
8
25
XIN / R33
R12 / INT1 / BUZO
8
21
XIN / R33
R13
9
24
R32 / AN15
R13
9
20
R32 / AN15
R14
10
23
R31 / AN14
R14
10
19
R31 / AN14
R15
11
22
R30 / AN13
R15
11
18
R30 / AN13
R16
12
21
R27
R16
12
17
R26 / AN12
R17 / AN8
13
20
R26 / AN12
R17 / AN8
13
16
R25 / AN11
R20
14
19
R25 / AN11
R23 / AN9
14
15
R24 / AN10
R21
15
18
R24 / AN10
R22
16
17
R23 / AN9
28 QFN
R30 / AN13
R06 / AN6 / T2O
15
R02 / AN2 / SOUT
R31 / AN14
27
16
2
XIN / R33
31
R32 / AN15
2
17
R03 / AN3 / INT2
XOUT / R34
28
18
1
R05 / AN5 / T0O
RESET / R35
R04 / AN4 / EC0
R02 / AN2 / SOUT
19
R03 / AN3 / INT2
20
32
VSS
1
21
R04/AN4 / EC0
R05 / AN5 / T0O
R00 / INT3 / SCK
22
14
R26 / AN12
28
8
R15
August 18, 2009 Ver 1.02
www.DataSheet.in
7
R16
R06 / AN6 / T2O
R14
9
6
27
5
R17 / AN8
R05 / AN5 / T0O
R13
10
R12 / INT1 / BUZO
26
4
R23 / AN9
R04 / AN4 / EC0
R11 / INT0 / PWM3O
11
3
25
2
R24 / AN10
R03 / AN3 / INT2
VDD
R25 / AN11
12
R10 / AN0 / AVREF / PWM1O
13
24
1
23
R07 / AN7 / EC1
R01 / AN1 / SI
R02 / AN2 / SOUT
5
MC80F0704/0708/0804/0808
4. PACKAGE DRAWING
28 SKINNY DIP
unit: inch
MAX
MIN
0.314
1.389
0.306
0.292
1.381
TYP 0.170
TYP 0.130
0.284
0.349
0.022
0.067
0.014
0.341
TYP 0.100
0.059
28 SOP
unit: millimetres
MAX
2.80 MAX
6
www.DataSheet.in
0.55
0.35
TYP 1.27
10.60
9.80
9.50
8.90
0.20
0.13
7.30
0.05 MIN
18.00
17.55
(STAND OFF)
7.90
MIN
0.70
0.30
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
32 SDIP
unit: millimeter
MAX
MIN
TYP 10.16
29.60
9.30
8.90
3.00
3.60
4.00
3.60
MIN 0.515
29.20
4
0.35
4
0.20
0.55
1.10
0.35
0 ~ 15°
TYP 1.778
0.90
32 SOP
unit: millimeter
MAX
2.55
2.35
August 18, 2009 Ver 1.02
www.DataSheet.in
0.45
0.35
TYP 1.27
10.60
10.20
TYP 0.40
0.20 MIN
21.30
21.20
7.45
7.55
MIN
0.95
0.55
0 ~ 8°
7
MC80F0704/0708/0804/0808
28 QFN
unit: millimetres
MAX
MIN
Top View
Bottom View
0.550
0.450
5.10
4.90
N22
N28
3.050
3.250
4.90
5.10
N1
3.250
3.050
N15
MIN. NORM. MAX.
A
0.700
0.750
0.850
0.300
0.180
0.800
0.800
0.050
0
0.050
0
N8
0.900
A
Side View
8
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
5. PIN FUNCTION
VDD: Supply voltage.
in Table 5-2
VSS: Circuit ground.
Port pin
Alternate function
XIN: Input to the inverting oscillator amplifier and input to the internal main clock operating circuit.
R10
XOUT: Output from the inverting oscillator amplifier.
R11
R00~R07: R0 is an 8-bit, CMOS, bidirectional I/O port. R0 pins
can be used as outputs or inputs according to “1” or “0” written
the their Port Direction Register(R0IO).
R12
AN0 ( Analog Input Port 0 )
AVref ( External Analog Reference Pin )
PWM1O ( PWM1 Output )
INT0 ( External Interrupt Input Port 0 )
PWM3O ( PWM3 Output )
INT1 ( External Interrupt Input Port 1 )
BUZ ( Buzzer Driving Output Port )
AN8 ( Analog Input Port 8 )
RESET: Reset the MCU.
Port pin
Alternate function
R00
INT3 ( External Interrupt Input Port3 )
SCK ( SPI CLK )
AN1 ( Analog Input Port 1 )
SI (SPI Serial Data Input )
AN2 ( Analog Input Port 2 )
SOUT ( SPI Serial Data Output )
AN3 ( Analog Input Port 3 )
INT2 ( External Interrupt Input Port2 )
AN4 ( Analog Input Port 4 )
EC0 ( Event Counter Input Source 0 )
AN5 ( Analog Input Port 5 )
T0O (Timer0 Clock Output )
AN6 ( Analog Input Port 6 )
T2O (Timer2 Clock Output )
AN7 ( Analog Input Port 7 )
EC1 ( Event Counter Input Source 1 )
R01
R02
R03
R04
R05
R06
R07
Table 5-1 R0 Port
In addition, R0 serves the functions of the various special features
in Table 5-1 .
R10~R17: R1 is an 8-bit, CMOS, bidirectional I/O port. R1 pins
can be used as outputs or inputs according to “1” or “0” written
the their Port Direction Register (R1IO).
R1 serves the functions of the various following special features
R13
R14
R15
R16
R17
Table 5-2 R1 Port
R20~R27 : R2 is an 8-bit, CMOS, bidirectional I/O port. R2 pins
can be used as outputs or inputs according to “1” or “0” written
the their Port Direction Register(R2IO)
In addition, R2 serves the functions of the various special features
in Table 5-3 .
Port pin
R20
R21
R22
R23
R24
R25
R26
R27
Alternate function
AN9 ( Analog Input Port 9 )
AN10 ( Analog Input Port 10 )
AN11 ( Analog Input Port 11 )
AN12 ( Analog Input Port 12 )
Table 5-3 R2 Port
R31~R35: R3 is a 6-bit, CMOS, bidirectional I/O port. R3 pins
can be used as outputs or inputs according to “1” or “0” written
the their Port Direction Register (R3IO).
R3 serves the functions of the serial interface following special
features in Table 5-4 .
Port pin
Alternate function
R30
R31
R32
R33
R34
R35
AN13 ( Analog Input Port 13)
AN14 ( Analog Input Port 14 )
AN15 ( Analog Input Port 15 )
XIN ( Oscillation Input )
XOUT ( Oscillation Output )
RESETB ( Reset input port )
Table 5-4 R3 Port
August 18, 2009 Ver 1.02
www.DataSheet.in
9
MC80F0704/0708/0804/0808
Pin No.
PIN NAME
Function
In/Out
32
28
28
QFN
VDD
5
5
2
-
Supply voltage
VSS
28
24
21
-
Circuit ground
RESET (R35)
27
23
20
I
Reset signal input
XIN (R33)
25
21
18
I
XOUT (R34)
26
22
19
O
First
Second
Third
Forth
Input only port
-
-
Oscillation Input
Normal I/O Port
-
-
Oscillation Output
Normal I/O Port
-
-
R00 (INT3/SCK)
29
25
22
I/O
External Interrupt 3
SPI clock Input
-
R01 (AN1/SI)
30
26
23
I/O
Analog Input Port 1
SPI Data Input
-
R02 (AN2/SOUT)
31
27
24
I/O
Analog Input Port 2
SPI Data Output
-
R03 (AN3/INT2)
32
28
25
I/O
Analog Input Port 3
External Interrupt2
-
R04 (AN4/EC0)
1
1
26
I/O
Analog Input Port 4
Event Counter
-
R05 (AN5/T0O)
2
2
27
I/O
Analog Input Port 5
Timer0 Output
-
R06 (AN6/T2O)
3
3
28
I/O
Analog Input Port 6
Timer2 Output
-
R07 (AN7/EC1)
4
4
1
I/O
Analog Input Port 7
Event Counter
-
R10 (AN0/AVref/
PWM1O)
6
6
3
I/O
Analog Input Port 0
Analog Reference
PWM 1 output
R11 (INT0/PWM3O)
7
7
4
I/O
External Interrupt 0
PWM 3 output
-
R12 (INT1/BUZO)
8
8
5
I/O
External Interrupt 1
Buzzer Driving
Output
-
R13
9
9
6
I/O
-
-
-
R14
10
10
7
I/O
-
-
-
R15
11
11
8
I/O
-
-
-
R16
12
12
9
I/O
-
-
-
R17
13
13
10
I/O
Analog Input Port 8
-
-
R20
14
-
-
I/O
-
-
-
R21
15
-
-
I/O
-
-
-
R22
16
-
-
I/O
-
-
-
R23
17
14
11
I/O
Analog Input Port 9
-
-
R24
18
15
12
I/O
Analog Input Port 10
-
-
R25
19
16
13
I/O
Analog Input Port 11
-
-
R26
20
17
14
I/O
Analog Input Port 12
-
-
R27
21
-
-
I/O
-
-
-
Normal I/O Ports
R30(AN13)
22
18
15
I/O
Analog Input Port 13
-
-
R31 (AN14)
23
19
16
I/O
Analog Input Port 14
-
-
R32 (AN15)
24
20
17
I/O
Analog Input Port 15
-
-
Table 5-5 Pin Description
10
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
6. PORT STRUCTURES
R13~R16,R20~R22,R27
R01 (AN1 / SI)
VDD
VDD
Pull-up
Reg.
Pull-up
Tr.
Pull-up
Reg.
Pull-up
Tr.
Open Drain
Reg.
Open Drain
Reg.
VDD
VDD
Direction
Reg.
Pin
Pin
Data Bus
VSS
MUX
VSS
VSS
VDD
Data Reg.
Data Reg.
Direction
Reg.
VDD
VSS
RD
Data Bus
MUX
AN[1]
RD
ADEN & ADS[3:0]
(ADCM)
Noise
Filter
SI
SI_EN (SIOM)
R17,R30~R32,R23~R26(AN8 ~ AN15)
R03 (AN3/INT2), R04 (AN4/EC0),R07 (AN7/EC1)
VDD
VDD
Pull-up
Tr.
Pull-up
Reg.
Open Drain
Reg.
VDD
Open Drain
Reg.
VDD
Data Reg.
VDD
VDD
Data Reg.
Direction
Reg.
Pin
VSS
Data Bus
Pull-up
Tr.
Pull-up
Reg.
VSS
Direction
Reg.
Data Bus
AN[15:14]
ADEN & ADS[3:0] (ADCM)
MUX
VSS
VSS
RD
MUX
RD
Pin
AN[3, 7]
ADEN & ADS[3:0]
(ADCM)
INT2, EC1, EC0
Noise
Filter
INT2E (PSR0.2), EC1E (PSR0.5), EC0E (PSR0.4)
August 18, 2009 Ver 1.02
www.DataSheet.in
11
MC80F0704/0708/0804/0808
R11 (INT0 / PWM3O), R12 (INT1 / BUZO)
R00 (INT3 / SCK)
VDD
VDD
Pull-up
Tr.
Pull-up
Reg.
Open Drain
Reg.
Data Reg.
Pull-up
Tr.
Pull-up
Reg.
Open Drain
Reg.
VDD
VDD
Data Reg.
MUX
MUX
SCK
PWM3O, BUZO
Pin
PWM3OE(PSR0.7)
BUZOE(PSR1.2)
Direction
Reg.
Pin
SCKO_EN(SIOM)
VSS
VSS
VSS
VSS
Direction
Reg.
Data Bus
Data Bus
VDD
VDD
MUX
MUX
RD
RD
Noise
Filter
SCK
Noise
Filter
INT0,INT1
SCK_EN(SIOM)
INT0E(PSR0.0)
INT1E(PSR0.1)
Noise
Filter
INT3
INT3E(PSR0.3)
R02 (AN2 / SOUT)
R06 (AN6 / T2O / ACLK)
VDD
VDD
Pull-up
Tr.
Pull-up
Reg.
Open Drain
Reg.
Data Reg.
VDD
Pull-up
Tr.
Pull-up
Reg.
Open Drain
Reg.
VDD
VDD
Data Reg.
MUX
MUX
T2O
SOUT
Pin
SO_EN(SIOM)
VSS
Direction
Reg.
VSS
Pin
T2OE(PSR1.1)
VSS
Direction
Reg.
Data Bus
Data Bus
VDD
VSS
MUX
MUX
RD
RD
AN[2]
ADEN & ADS[3:0]
(ADCM)
SOUT(SI)
SO_OUT_EN (SIOM)
AN[6]
Noise
Filter
ADEN & ADS[3:0]
(ADCM)
ACLK
Noise
Filter
TPS[2:0](BRGCR[6:4])
12
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
R10 (AN0 / AVREF / PWM1O)
RESET
VDD
Pull-up
Tr.
Pull-up
Reg.
Open Drain
Reg.
VDD
Data Reg.
VDD
MUX
PWM1O
Pin
Pull-up
Reg.
PWM1OE(PSR0.6)
Direction
Reg.
VDD
RD
VSS
VSS
VDD
Pull-up
Tr.
Mask only
Data Bus
Data Bus
Pin
Internal Reset
MUX
RD
VSS
Reset Disable
(Configuration option bit)
AN[0]
ADEN & ADS[3:0]
(ADCM)
ADC Reference
Voltage Input
VDD
MUX
AVREFS(PSR1.3)
R05 (AN5 / T0O), R06 (AN6 / T2O)
XIN, XOUT (Crystal or Ceramic Resonator)
VDD
Pull-up
Tr.
Pull-up
Reg.
Open Drain
Reg.
Data Reg.
VDD
VDD
VDD
VDD
MUX
T0O, T2O
Pin
T0OE(PSR1.0)
T2OE(PSR1.1)
XIN
STOP
VSS
Direction
Reg.
VSS
VSS
VDD
VDD
Data Bus
MUX
RD
AN[5], AN[6]
MAIN
CLOCK
XOUT
VSS
ADEN & ADS[3:0]
(ADCM)
August 18, 2009 Ver 1.02
www.DataSheet.in
13
MC80F0704/0708/0804/0808
XIN, XOUT (External RC or R oscillation)
R33 (XIN), R34 (XOUT)
VDD
Pull-up
Tr.
Pull-up
Reg.
Open Drain
Reg.
VDD
VDD
Direction
Reg.
XIN
/ R33
VSS
VSS
MAIN
CLOCK
Data Bus
VDD
fXIN ÷ 4
XOUT
VSS
VDD
Data Reg.
XIN
STOP
VDD
IN4MCLK
IN2MCLK
IN4MCLKXO
IN2MCLKXO
CLOCK option
(Configuration
option bit)
VSS
MUX
RD
IN4MCLK
IN2MCLK
EXRC
Main Clock
(to ONP Block)
VDD
Pull-up
Tr.
Pull-up
Reg.
Open Drain
Reg.
VDD
VDD
Data Reg.
Direction
Reg.
XOUT
/ R34
VSS
Data Bus
VSS
MUX
RD
System Clock ÷ 4
IN4MCLKXO
IN2MCLKCO
EXRCXO
CLOCK option
(Configuration option bit)
14
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
7. ELECTRICAL CHARACTERISTICS
7.1 Absolute Maximum Ratings
Supply voltage........................................................ -0.3 to +6.0 V
............................................................................................10 mA
Storage Temperature .............................................-65 to +125 °C
Maximum current (ΣIOL) .................................................160 mA
Voltage on any pin with respect to Ground (VSS)
..........................................................................-0.3 to VDD+0.3V
Maximum current (ΣIOH)...................................................80 mA
Maximum current out of VSS pin.....................................180 mA
Note: Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at any other conditions above those indicated in the operational sections of
this specification is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
Maximum current into VDD pin .........................................80 mA
Maximum current sunk by (IOL per I/O Pin) .....................20 mA
Maximum output current sourced by (IOH per I/O Pin)
7.2 Recommended Operating Conditions
Parameter
Symbol
Condition
Supply Voltage
Operating Frequency
Operating Temperature
Specifications
Unit
Min.
Max.
VDD
fXIN=1~12MHz
fXIN=1~8MHz
fXIN=1~6MHz
fXIN=1~4MHz
4.5
3.0
2.7
2.2
5.5
5.5
5.5
5.5
V
fXIN
VDD=4.5~5.5V
VDD=3.0~5.5V
VDD=2.7~5.5V
VDD=2.2~5.5V
1
1
1
1
12
8
6
4
MHz
TOPR
VDD =2.7~5.5V
-40
85
°C
7.3 A/D Converter Characteristics
(Ta = -40~85°C, VSS = 0V, VDD =AVREF= 5.12V, 3.072V
Parameter
Symbol
Conditions
Min.
Typ.
Max.
Unit
-
-
10
-
BIT
-
-
-
±3
LSB
NNLE
-
−
±3
LSB
NDNLE
-
−
±3
LSB
-
−
±3
LSB
Resolution
Overall Accuracy
Non Liniearity Error
Differential NON Linearity Error
-
fXIN=4MHz
Zero Offset Error
NZOE
Full Scale Error
NFSE
-
−
±3
LSB
Gain Error
NGE
-
-
±3
LSB
Conversion Time
Analog Input Voltage
Analog Voltage Reference
Conversion Current
August 18, 2009 Ver 1.02
www.DataSheet.in
TCONV
-
13
-
-
μS
VAIN
-
VSS
-
VDD
(AVREF)
V
AVREF1
-
2.7V
-
VDD
V
ICON
VDD=5.12V, fXIN=8MHz
-
80
200
μA
15
MC80F0704/0708/0804/0808
1. If the AVREF voltage is less than VDD voltage and anlalog input pins(ANX), shared with various alternate function, are used bidirectional
I/O port, the leakage current may flow VDD pin to AVREF pin in output high mode or anlalog input pins(ANX) to AVREF pin in input high
mode.
7.4 DC Electrical Characteristics
(TA=-40~85°C, VDD=5.0V, VSS=0V),
Parameter
Symbol
VIH1
Pin
Condition
Specifications
Typ.
Max.
0.8 VDD
-
VDD
Unit
VDD
0.8 VDD
XIN, RESET
Min.
VIH2
Hysteresis
VIH3
Normal Input
0.7 VDD
-
VDD
VIL1
XIN, RESET
0
-
0.2 VDD
VIL2
Hysteresis Input1
0
-
0.2 VDD
VIL3
Normal Input
0
-
0.3 VDD
Output High Voltage
VOH
All Output Port
VDD=5V, IOH=-5mA
VDD -1
-
-
V
Output Low Voltage
VOL
All Output Port
VDD=5V, IOL=10mA
-
-
1
V
Input Pull-up Current
IP
Normal Input
VDD=5V
-60
-
-150
μA
Input High Voltage
Input Low Voltage
Input1
V
V
Input High
Leakage Current
IIH1
All Pins (except XIN)
VDD=5V
-
-
5
μA
IIH2
XIN
VDD=5V
-
-
13
μA
Input Low
Leakage Current
IIL1
All Pins (except XIN)
VDD=5V
-5
-
-
μA
IIL2
XIN
VDD=5V
-13
-
-
μA
VDD=5V
0.5
-
-
V
2.0
2.8
3.2
V
25
65
95
μS
Hysteresis
| VT |
Hysteresis Input1
PFD Voltage
VPFD
VDD
TRCWDT
XOUT
VDD=5.0V
Operating Current2
IDD
VDD
VDD=5.5V,fXIN=12MHz
-
8.8
15
mA
Sleep Mode Current
ISLEEP
VDD
VDD=5.5V,fXIN=12MHz
-
1
2
mA
RCWDT Mode Current at STOP Mode
IRCWDT
VDD
VDD=5.5V,fXIN=12MHz
-
20
50
μA
Stop Mode Current
ISTOP
VDD
VDD=5.5V,fXIN=12MHz
-
4
10
μA
Internal 4MHz Oscillation Frequency
TIN4MCLK
XOUT
VDD=5V, 25°C
3.5
4
4.5
MHz
Internal 2MHz Oscillation Frequency
TIN2MCLK
XOUT
VDD=5V, 25°C
1.75
2
2.25
MHz
VDD Rising Time
TVDD3
VDD
-
-
40
ms/V
VDD Start Voltage
VSTART3
VDD
VSS
-
0.7
V
Config Read Voltage
VCONFIG3 VDD
1.8
-
-
V
2.4
2.9
3.4
V
Internal RC WDT
Period
Power On Reset
16
www.DataSheet.in
VPOR
VDD
TVDD=40ms/V,
VSTART=VSS
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
Parameter
Symbol
Pin
External RC
Oscillator Frequency
fRC-OSC
fXOUT = fRC-OSC ÷ 4
VDD=5.5V
R=30kΩ, C=10pF
fR-OSC
fXOUT = fR-OSC ÷ 4
Specifications
Condition
VDD=5.5V, R=30kΩ
Unit
Min.
Typ.
Max.
0.5
1.5
2.5
MHz
1
2
3
MHz
1. Hysteresis Input: INT0 ~INT3(R11,R12,R03,R00),SIO(R00,R01,R02), EC0,EC1(R04,R07)
2. This parameter is measured in internal PROM operation at the all I/O port defined input mode.
3. These parameters are presented for design guidance only and not tested or guaranteed.
V
VDD
TVDD ≤ 40ms/V
VDDMIN
Config(POR) Read
Detection Point
Config(POR) Read
Detection Point
VCONFIG
No Config(POR) Read
VSTART
0V
T
Figure 7-1 Config Read Voltage including POR vs Supply Voltage
7.5 AC Characteristics
(TA=-40~+85°C, VDD=5V±10%, VSS=0V)
Parameter
Symbol
Pins
fCP
Specifications
Unit
Min.
Typ.
Max.
XIN
1
-
12
MHz
tCPW
XIN
35
-
-
nS
tRCP,tFCP
XIN
-
-
20
nS
tST
XIN, XOUT
-
-
20
mS
External Input Pulse Width
tEPW
INT0, INT1, INT2, INT3
EC0, EC1
2
-
-
tSYS
RESET Input Width
tRST
RESET
8
-
-
tSYS
Operating Frequency
External Clock Pulse Width
External Clock Transition Time
Oscillation Stabilizing Time(4MHz)
August 18, 2009 Ver 1.02
www.DataSheet.in
17
MC80F0704/0708/0804/0808
1/fCP
tCPW
tCPW
VDD-0.5V
XIN
0.5V
tSYS
tRCP
tFCP
tRST
RESET
0.2VDD
tEPW
tEPW
0.8VDD
INT0, INT1
INT2, INT3
EC0, EC1
0.2VDD
Figure 7-2 Timing Chart
18
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
7.6 Typical Characteristics
These graphs and tables provided in this section are for design
guidance only and are not tested or guaranteed.
In some graphs or tables the data presented are outside specified operating range (e.g. outside specified
VDD range). This is for information only and devices
are guaranteed to operate properly only within the
specified range.
The data presented in this section is a statistical summary of data
collected on units from different lots over a period of time. “Typical” represents the mean of the distribution while “max” or
“min” represents (mean + 3σ) and (mean − 3σ) respectively
where σ is standard deviation.
Operating Area
fXIN
(MHz)
Normal Operation
IDD−VDD
Ta=25°C
16
14
IDD
(mA)
12
12
10
10
8
8
6
6
4
4
2
2
Ta=25°C
fXIN=12MHz
0
2
3
4
VDD
(V)
6
5
0
2
STOP Mode
ISTOP−VDD
IDD
(μA)
4MHz
3
4
5
VDD
6 (V)
5
VDD
6 (V)
SLEEP Mode
ISLEEP−VDD
IDD
(mA)
Ta=25°C
2
1.5
1.5
1
1.0
0.5
Ta=25°C
2.0
0.5
0
2
3
4
VDD
(V)
5
fXIN = 12MHz
0
2
3
4
RC-WDT in Stop Mode
IRCWDT−VDD
IDD
(μA)
Ta=25°C
20
15
TRCWDT = 50uS
10
5
0
2
3
August 18, 2009 Ver 1.02
www.DataSheet.in
4
5
VDD
6 (V)
19
MC80F0704/0708/0804/0808
IOL−VOL, VDD=5V
IOH−VOH, VDD=5V
IOL
(mA)
IOH
(mA)
-25°C
25°C
20
-25°C
25°C
-20
85°C
85°C
15
-15
10
-10
5
-5
0
0.5
VIH1
(V)
4
1
1.5
2
VDD−VIH1
XIN, RESET
0
VOL
(V)
3.5
VDD−VIH2
VIH2
(V)
fXIN=4MHz
Ta=25°C
4
Hysteresis input
fXIN=4kHz
Ta=25°C
4
4.5
VDD−VIH3
VIH3
(V)
4
3
3
2
2
1
1
1
0
1
VIL1
(V)
4
2
3
4
5
VDD
6 (V)
VDD−VIL1
XIN, RESET
0
2
3
VDD−VIL2
VIL2
(V)
fXIN=4MHz
Ta=25°C
4
4
5
VDD
6 (V)
Hysteresis input
fXIN=4kHz
Ta=25°C
0
2
3
VDD−VIL3
VIL3
(V)
4
3
3
2
1
5
VDD
6 (V)
Normal input
fXIN=4kHz
Ta=25°C
2
1
4
3
2
1
0
1
www.DataSheet.in
Normal input
fXIN=4kHz
Ta=25°C
3
2
20
VOH
(V)
5
2
3
4
5
VDD
6 (V)
0
2
3
4
5
VDD
6 (V)
0
2
3
4
5
VDD
6 (V)
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
Typical RC Oscillator
Frequency vs VDD
FOSC
(MHz)
10
Typical RC Oscillator
Frequency vs VDD
FOSC
(MHz)
No Cap
Ta = 25°C
10
CEXT = 10pF
Ta = 25°C
9
9
R = 4.7K
8
8
7
7
R = 10K
6
R = 4.7K
6
R = 10K
5
5
4
4
R = 20K
3
3
R = 20K
R = 30K
2
2
1
1
0
2.5
3.0
3.5
4.0
4.5
5.0
FOSC
(MHz)
7
0
VDD
5.5 (V)
Typical RC Oscillator
Frequency vs VDD
2.5
7
6
3.0
3.5
4.0
4.5
5.0
VDD
5.5 (V)
Typical RC Oscillator
Frequency vs VDD
FOSC
(MHz)
CEXT = 20pF
Ta = 25°C
R = 30K
CEXT = 30pF
Ta = 25°C
6
R = 4.7K
R = 4.7K
5
5
4
4
R = 10K
3
2
2
R = 30K
1
2.5
3.0
3.5
4.0
4.5
5.0
VDD
5.5 (V)
Note: The external RC oscillation frequencies shown in
above are provided for design guidance only and not tested
or guaranteed. The user needs to take into account that the
external RC oscillation frequencies generated by the same
circuit design may be not the same. Because there are variations in the resistance and capacitance due to the tolerance of external R and C components. The parasitic
capacitance difference due to the different wiring length
and layout may change the external RC oscillation frequencies.
August 18, 2009 Ver 1.02
R = 20K
1
0
www.DataSheet.in
R = 10K
3
R = 20K
R = 30K
0
2.5
3.0
3.5
4.0
4.5
5.0
VDD
5.5 (V)
Note: There may be the difference between package
types(PDIP, SOP, TSSOP). The user should modify the
value of R and C components to get the proper frequency
in MC80F0704/0708/0804/0808 or one package type to
another package type.
21
MC80F0704/0708/0804/0808
by sample, voltage and temperature. The internal oscillation can be used only in timing insensitive application.
Typical Internal 4MHz
Frequency vs VDD
FOSC
(MHz)
Ta = 25°C
5
4.5
4
3.5
2.5
3.0
3.5
4.0
4.5
5.0
VDD
5.5 (V)
Note: The internal 4MHz oscillation frequencies shown in
above are provided for design guidance only and not tested
or guaranteed. The user needs to take into account that the
internal oscillation of the MC80F0704/0708/0804/0808 or
MC80F0808(4) may show different frequency with sample
22
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
8. MEMORY ORGANIZATION
The MC80F0704/0708/0804/0808 has separate address spaces
for Program memory and Data Memory. 4K bytes program memory can only be read, not written to.
Data memory can be read and written to up to 256 bytes including
the stack area.
8.1 Registers
This device has six registers that are the Program Counter (PC),
a Accumulator (A), two index registers (X, Y), the Stack Pointer
(SP), and the Program Status Word (PSW). The Program Counter
consists of 16-bit register.
A
ACCUMULATOR
X
X REGISTER
Y
Y REGISTER
SP
PCL
The stack can be located at any position within 1C0H to 1FFH of
the internal data memory. The SP is not initialized by hardware,
requiring to write the initial value (the location with which the use
of the stack starts) by using the initialization routine. Normally,
the initial value of “FFH” is used.
STACK POINTER
PROGRAM COUNTER
PSW
PCH
Generally, SP is automatically updated when a subroutine call is
executed or an interrupt is accepted. However, if it is used in excess of the stack area permitted by the data memory allocating
configuration, the user-processed data may be lost.
PROGRAM STATUS WORD
Bit 15
Stack Address (1C0H ~ 1FFH)
8 7
Bit 0
01H
SP
C0H~FFH
Hardware fixed
Figure 8-1 Configuration of Registers
Accumulator: The Accumulator is the 8-bit general purpose register, used for data operation such as transfer, temporary saving,
and conditional judgement, etc.
The Accumulator can be used as a 16-bit register with Y Register
as shown below.
Y
Y
A
A
Two 8-bit Registers can be used as a “YA” 16-bit Register
Figure 8-2 Configuration of YA 16-bit Register
X, Y Registers: In the addressing mode which uses these index
registers, the register contents are added to the specified address,
which becomes the actual address. These modes are extremely effective for referencing subroutine tables and memory tables. The
index registers also have increment, decrement, comparison and
data transfer functions, and they can be used as simple accumulators.
Stack Pointer: The Stack Pointer is an 8-bit register used for occurrence interrupts and calling out subroutines. Stack Pointer
identifies the location in the stack to be accessed (save or restore).
August 18, 2009 Ver 1.02
www.DataSheet.in
Note: The Stack Pointer must be initialized by software because its value is undefined after Reset.
Example: To initialize the SP
LDX
#0FFH
TXSP
; SP ← FFH
Program Counter: The Program Counter is a 16-bit wide which
consists of two 8-bit registers, PCH and PCL. This counter indicates the address of the next instruction to be executed. In reset
state, the program counter has reset routine address (PCH:0FFH,
PCL:0FEH).
Program Status Word: The Program Status Word (PSW) contains several bits that reflect the current state of the CPU. The
PSW is described in Figure 8-3 . It contains the Negative flag, the
Overflow flag, the Break flag the Half Carry (for BCD operation), the Interrupt enable flag, the Zero flag, and the Carry flag.
[Carry flag C]
This flag stores any carry or borrow from the ALU of CPU after
an arithmetic operation and is also changed by the Shift Instruction or Rotate Instruction.
[Zero flag Z]
This flag is set when the result of an arithmetic operation or data
transfer is “0” and is cleared by any other result.
23
MC80F0704/0708/0804/0808
PSW
MSB
N V G B H
NEGATIVE FLAG
OVERFLOW FLAG
SELECT DIRECT PAGE
when G=1, page is selected to “page 1”
BRK FLAG
I
Z
LSB
C RESET VALUE: 00H
CARRY FLAG RECEIVES
CARRY OUT
ZERO FLAG
INTERRUPT ENABLE FLAG
HALF CARRY FLAG RECEIVES
CARRY OUT FROM BIT 1 OF
ADDITION OPERLANDS
Figure 8-3 PSW (Program Status Word) Register
[Interrupt disable flag I]
This flag enables/disables all interrupts except interrupt caused
by Reset or software BRK instruction. All interrupts are disabled
when cleared to “0”. This flag immediately becomes “0” when an
interrupt is served. It is set by the EI instruction and cleared by
the DI instruction.
[Half carry flag H]
After operation, this is set when there is a carry from bit 3 of ALU
or there is no borrow from bit 4 of ALU. This bit can not be set
or cleared except CLRV instruction with Overflow flag (V).
[Break flag B]
This flag is set by software BRK instruction to distinguish BRK
from TCALL instruction with the same vector address.
[Direct page flag G]
24
www.DataSheet.in
This flag assigns RAM page for direct addressing mode. In the direct addressing mode, addressing area is from zero page 00H to
0FFH when this flag is " 0 " . If it is set to " 1 " , addressing area is
assigned 100H to 1FFH. It is set by SETG instruction and cleared
by CLRG.
[Overflow flag V]
This flag is set to “1” when an overflow occurs as the result of an
arithmetic operation involving signs. An overflow occurs when
the result of an addition or subtraction exceeds +127(7FH) or 128(80H). The CLRV instruction clears the overflow flag. There
is no set instruction. When the BIT instruction is executed, bit 6
of memory is copied to this flag.
[Negative flag N]
This flag is set to match the sign bit (bit 7) status of the result of
a data or arithmetic operation. When the BIT instruction is executed, bit 7 of memory is copied to this flag.
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
At acceptance
of interrupt
At execution of
a CALL/TCALL/PCALL
01FF
Push
down
01FF
PCH
01FE
PCL
01FD
01FD
PSW
01FC
At execution
of RET instruction
01FC
01FE
PCH
PCL
01FF
01FF
PCH
01FE
PCL
01FD
01FD
PSW
01FC
Push
down
PCH
01FE
PCL
At execution
of RET instruction
01FC
Pop
up
SP before
execution
01FF
01FF
01FD
01FC
SP after
execution
01FD
01FC
01FF
Pop
up
01FF
At execution
of PUSH instruction
PUSH A (X,Y,PSW)
01FF
A
01FE
Push
down
At execution
of POP instruction
POP A (X,Y,PSW)
01FF
A
01FE
01FD
01FC
01C0H
01FD
01FC
Pop
up
Stack
depth
01FFH
SP before
execution
01FF
01FE
SP after
execution
01FE
01FF
Figure 8-4 Stack Operation
August 18, 2009 Ver 1.02
www.DataSheet.in
25
MC80F0704/0708/0804/0808
8.2 Program Memory
A 16-bit program counter is capable of addressing up to 64K
bytes, but this device has 4K/8K/16K bytes program memory
space only physically implemented. Accessing a location above
FFFFH will cause a wrap-around to 0000H.
Figure 8-5 , shows a map of Program Memory. After reset, the
CPU begins execution from reset vector which is stored in address FFFEH and FFFFH as shown in Figure 8-6 .
As shown in Figure 8-5 , each area is assigned a fixed location in
Program Memory. Program Memory area contains the user program
C000H
FFC0H
FFDFH
FFE0H
FFFFH
TCALL area
Interrupt
Vector Area
8K ROM
4K ROM
FEFFH
FF00H
PCALL area
F000H
16K ROM
E000H
Example: Usage of TCALL
LDA
#5
TCALL 0FH
:
:
;1BYTE INSTRUCTION
;INSTEAD OF 3 BYTES
;NORMAL CALL
;
;TABLE CALL ROUTINE
;
FUNC_A: LDA
LRG0
RET
;
FUNC_B: LDA
LRG1
2
RET
;
;TABLE CALL ADD. AREA
;
ORG
0FFC0H
DW
FUNC_A
DW
FUNC_B
1
;TCALL ADDRESS AREA
The interrupt causes the CPU to jump to specific location, where
it commences the execution of the service routine. The External
interrupt 0, for example, is assigned to location 0FFFCH. The interrupt service locations spaces 2-byte interval: 0FFFAH and
0FFFBH for External Interrupt 1, 0FFFCH and 0FFFDH for External Interrupt 0, etc.
Any area from 0FF00H to 0FFFFH, if it is not going to be used,
its service location is available as general purpose Program Memory.
Figure 8-5 Program Memory Map
Page Call (PCALL) area contains subroutine program to reduce
program byte length by using 2 bytes PCALL instead of 3 bytes
CALL instruction. If it is frequently called, it is more useful to
save program byte length.
Table Call (TCALL) causes the CPU to jump to each TCALL address, where it commences the execution of the service routine.
The Table Call service area spaces 2-byte for every TCALL:
0FFC0H for TCALL15, 0FFC2H for TCALL14, etc., as shown in
Figure 8-7 .
Address
0FFE0H
Vector Area Memory
Basic Interval Timer
E2
Watchdog Timer Interrupt
E4
A/D Converter
E6
-
E8
Timer/Counter 3 Interrupt
EA
Timer/Counter 2 Interrupt
EC
Timer/Counter 1 Interrupt
EE
Timer/Counter 0 Interrupt
F0
Serial Input/Output (SIO)
F2
-
F4
-
F6
External Interrupt 3
F8
External Interrupt 2
FA
External Interrupt 1
FC
External Interrupt 0
FE
RESET
Figure 8-6 Interrupt Vector Area
26
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
PCALL Area Memory
Address
PCALL Area
(256 Bytes)
Address
0FF00H
0FFC0H
C1
C2
C3
C4
C5
C6
C7
C8
C9
CA
CB
CC
CD
CE
CF
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
DC
DD
DE
DF
0FFFFH
Program Memory
TCALL 15
TCALL 14
TCALL 13
TCALL 12
TCALL 11
TCALL 10
TCALL 9
TCALL 8
TCALL 7
TCALL 6
TCALL 5
TCALL 4
TCALL 3
TCALL 2
TCALL 1
TCALL 0 / BRK *
NOTE:
* means that the BRK software interrupt is using
same address with TCALL0.
Figure 8-7 PCALL and TCALL Memory Area
PCALL→ rel
TCALL→ n
4F35
4A
PCALL 35H
TCALL 4
4A
~
~
4F
0D125H
35
~
~
~
~
0FF00H
0FF35H
➊
~
~
NEXT
➌
0FF00H
FH
DH 6H
➋
25
0FFD7H
Reverse
PC: 11111111 11010110
FH
0FFD6H
NEXT
01001010
D1
0FFFFH
0FFFFH
August 18, 2009 Ver 1.02
www.DataSheet.in
Example: The usage software example of Vector address
27
MC80F0704/0708/0804/0808
8.3 Data Memory
blocks for controlling the desired operation of the device. Therefore these registers contain control and status bits for the interrupt
system, the timer/ counters, analog to digital converters and I/O
ports. The control registers are in address range of 0C0H to 0FFH.
Figure 8-8 shows the internal Data Memory space available.
Data Memory is divided into three groups, a user RAM, control
registers, and Stack memory.
0000H
Note that unoccupied addresses may not be implemented on the
chip. Read accesses to these addresses will in general return random data, and write accesses will have an indeterminate effect.
User Memory
(192Bytes)
More detailed informations of each register are explained in each
peripheral section.
PAGE0
00BFH
00C0H
(When “G-flag=0”,
this page0 is selected)
Control
Registers
00FFH
0100H
Note: Write only registers can not be accessed by bit manipulation instruction. Do not use read-modify-write instruction. Use byte manipulation instruction, for example “LDM”.
Not Available
01BFH
01C0H
Example; To write at CKCTLR
PAGE1
LDM
User Memory
or Stack Area
(64 bytes)
01FFH
CKCTLR,#0AH ;Divide ratio(÷32)
Stack Area
The stack provides the area where the return address is saved before a jump is performed during the processing routine at the execution of a subroutine call instruction or the acceptance of an
interrupt.
Figure 8-8 Data Memory Map
User Memory
When returning from the processing routine, executing the subroutine return instruction [RET] restores the contents of the program counter from the stack; executing the interrupt return
instruction [RETI] restores the contents of the program counter
and flags.
The MC80F0704/0708/0804/0808 has 256 × 8 bits for the user
memory (RAM). RAM pages are selected by RPR (See Figure 89 ).
Note: After setting RPR(RAM Page Select Register), be
sure to execute SETG instruction. When executing CLRG
instruction, be selected PAGE0 regardless of RPR.
The save/restore locations in the stack are determined by the
stack pointed (SP). The SP is automatically decreased after the
saving, and increased before the restoring. This means the value
of the SP indicates the stack location number for the next save.
Refer to Figure 8-4 on page 25.
Control Registers
The control registers are used by the CPU and Peripheral function
7
RPR
6
5
4
3
-
-
-
-
-
R/W
2
-
R/W
1
R/W
0
RPR1 RPR0
ADDRESS: 0E1H
INITIAL VALUE: ---- --00B
System clock source select
00 : PAGE0
01 : PAGE1
others : Setting prohibited
Figure 8-9 RPR(RAM Page Select Register)
28
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
Address
Register Name
Symbol
Initial Value
R/W
7 6 5 4 3 2 1 0
Addressing
Mode
R0
R/W
0 0 0 0 0 0 0 0
byte, bit1
R0IO
W
0 0 0 0 0 0 0 0
byte2
R1
R/W
0 0 0 0 0 0 0 0
byte, bit
R1IO
W
0 0 0 0 0 0 0 0
byte
R2
R/W
0 0 0 0 0 0 0 0
byte, bit
R2IO
W
0 0 0 0 0 0 0 0
byte
R3
R/W
-
- 0 0 0 0 0 0
byte, bit
R3 port I/O direction register
R3IO
W
-
- 0 0 0 0 0 0
byte
00C8
Port 0 Open Drain Selection Register
R0OD
W
0 0 0 0 0 0 0 0
byte
00C9
Port 1 Open Drain Selection Register
R1OD
W
0 0 0 0 0 0 0 0
byte
00CA
Port 2 Open Drain Selection Register
R2OD
W
0 0 0 0 0 0 0 0
byte
00CB
Port 3 Open Drain Selection Register
R3OD
W
-
- 0 0 0 0 0 0
byte
00D0
Timer 0 mode control register
TM0
R/W
-
- 0 0 0 0 0 0
byte, bit
T0
R
0 0 0 0 0 0 0 0
Timer 0 data register
TDR0
W
1 1 1 1 1 1 1 1
Timer 0 capture data register
CDR0
R
0 0 0 0 0 0 0 0
Timer 1 mode control register
TM1
R/W
0 0 0 0 0 0 0 0
byte, bit
TDR1
W
1 1 1 1 1 1 1 1
byte
T1PPR
W
1 1 1 1 1 1 1 1
byte
T1
R
0 0 0 0 0 0 0 0
Timer 1 capture data register
CDR1
R
0 0 0 0 0 0 0 0
Timer 1 PWM duty register
T1PDR
R/W
0 0 0 0 0 0 0 0
00D5
Timer 1 PWM high register
T1PWHR
W
-
-
00D6
Timer 2 mode control register
TM2
R/W
-
- 0 0 0 0 0 0
T2
R
0 0 0 0 0 0 0 0
Timer 2 data register
TDR2
W
1 1 1 1 1 1 1 1
Timer 2 capture data register
CDR2
R
0 0 0 0 0 0 0 0
Timer 3 mode control register
TM3
R/W
0 0 0 0 0 0 0 0
TDR3
W
1 1 1 1 1 1 1 1
T3PPR
W
1 1 1 1 1 1 1 1
T3
R
0 0 0 0 0 0 0 0
Timer 3 PWM duty register
T3PDR
R/W
0 0 0 0 0 0 0 0
Timer 3 capture data register
CDR3
R
0 0 0 0 0 0 0 0
00C0
R0 port data register
00C1
R0 port I/O direction register
00C2
R1 port data register
00C3
R1 port I/O direction register
00C4
R2 port data register
00C5
R2 port I/O direction register
00C6
R3 port data register
00C7
Timer 0 register
00D1
00D2
00D3
Timer 1 data register
Timer 1 PWM period register
Timer 1 register
00D4
Timer 2 register
00D7
00D8
00D9
Timer 3 data register
Timer 3 PWM period register
Timer 3 register
00DA
-
- 0 0 0 0
byte
byte
byte
bit
byte, bit
byte
byte, bit
byte
byte
Table 8-1 Control Registers
August 18, 2009 Ver 1.02
www.DataSheet.in
29
MC80F0704/0708/0804/0808
Address
Register Name
Symbol
Initial Value
R/W
7 6 5 4 3 2 1 0
00DB
Timer 3 PWM high register
00E0
T3PWHR
W
-
- 0 0 0 0
byte
Buzzer driver register
BUZR
W
1 1 1 1 1 1 1 1
byte
00E1
RAM page selection register
RPR
R/W
-
- 0 0 0
byte, bit
00E2
SIO mode control register
SIOM
R/W
0 0 0 0 0 0 0 1
byte, bit
00E3
SIO data shift register
SIOR
R/W
Undefined
byte, bit
00EA
Interrupt enable register high
IENH
R/W
0 0 0 0 0 0 0 0
byte, bit
00EB
Interrupt enable register low
IENL
R/W
0 0 0 0 0 0 0 0
byte, bit
00EC
Interrupt request register high
IRQH
R/W
0 0 0 0 0 0 0 0
byte, bit
00ED
Interrupt request register low
IRQL
R/W
0 0 0 0 0 0 0 0
byte, bit
00EE
Interrupt edge selection register
IEDS
R/W
0 0 0 0 0 0 0 0
byte, bit
00EF
A/D converter mode control register
ADCM
R/W
0 0 0 0 0 0 0 1
byte, bit
00F0
A/D converter result high register
ADCRH
R(W)
0 1 0
00F1
A/D converter result low register
ADCRL
R
Undefined
BITR
R
Undefined
CKCTLR
W
0 - 0 1 0 1 1 1
WDTR
W
0 1 1 1 1 1 1 1
WDTDR
R
Undefined
0 0 0 0 0 0 0 0
00F2
00F4
Basic interval timer register
Clock control register
Watch dog timer register
Watch dog timer data register
-
-
-
Addressing
Mode
-
-
Undefined
byte
byte
byte
byte
00F5
Stop & sleep mode control register
SSCR
W
00F7
PFD control register
PFDR
R/W
00F8
Port selection register 0
PSR0
W
0 0 0 0 0 0 0 0
byte
00F9
Port selection register 1
PSR1
W
-
- 0 0 0 0
byte
00FC
Pull-up selection register 0
PU0
W
0 0 0 0 0 0 0 0
byte
00FD
Pull-up selection register 1
PU1
W
0 0 0 0 0 0 0 0
byte
00FD
pull-up selection register 2
PU2
W
0 0 0 0 0 0 0 0
byte
00FF
Pull-up selection register 3
PU3
W
-
byte
-
-
-
-
-
-
- 0 0 0
- 0 0 0 0 0 0
byte
byte, bit
Table 8-1 Control Registers
1.
The ‘byte, bit’ means registers are controlled by both bit and byte manipulation instruction.
Caution) The R/W register except T1PDR and T3PDR are both can be byte and bit manipulated.
2.
The ‘byte’ means registers are controlled by only byte manipulation instruction. Do not use bit manipulation
instruction such as SET1, CLR1 etc. If bit manipulation instruction is used on these registers,
content of other seven bits are may varied to unwanted value.
*The mark of ‘-’ means this bit location is reserved.
30
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
T0CK2
T0CK1
T0CK0
T0CN
T0ST
T1CN
T1ST
0C0H
R0
R0 Port Data Register
0C1H
R0IO
R0 Port Direction Register
0C2H
R1
R1 Port Data Register
0C3H
R1IO
R1 Port Direction Register
0C4H
R2
R2 Port Data Register
0C5H
R2IO
R2Port Data Register
0C6H
R3
R3 Port Data Register
0C7H
R3IO
R3 Port Direction Register
0C8H
R0OD
R0 Open Drain Selection Register
0C9H
R1OD
R1 Open Drain Selection Register
0CAH
R2OD
R2 Open Drain Selection Register
0CBH
R3OD
R3 Open Drain Selection Register
0D0H
TM0
0D1H
T0/TDR0/
CDR0
0D2H
TM1
0D3H
TDR1/
T1PPR
Timer1 Data Register / Timer1 PWM Period Register
0D4H
T1/CDR1
Timer1 Register / Timer1 Capture Data Register
0D5H
PWM1HR
-
-
-
-
0D6H
TM2
-
-
CAP2
T2CK2
0D7H
T2/TDR2/
CDR2
0D8H
TM3
0D9H
TDR3/
T3PPR
0DAH
T3/CDR3/
Timer3 Register / Timer3 Capture Data Register / Timer3 PWM Duty Register
T3PDR
0DBH
PWM3HR
0E0H
BUZR
0E1H
-
-
CAP0
Timer0 Register / Timer0 Data Register / Timer0 Capture Data Register
T1_POL
T1_16BIT
PWM1E
CAP1
T1CK1
T1CK0
Timer1 PWM High Register
T2CK1
T2CK0
T2CN
T2ST
T3CN
T3ST
Timer2 Register / Timer2 Data Register / Timer2 Capture Data Register
T3_POL
T3_16BIT
PWM3E
CAP3
T3CK1
T3CK0
Timer3 Data Register / Timer3 PWM Period Register
-
-
-
-
Timer3 PWM High Register
BUCK1
BUCK0
BUR5
BUR4
BUR3
BUR2
BUR1
BUR0
RPR
-
-
-
-
-
RPR2
RPR1
RPR0
0E2H
SIOM
POL
IOSW
SM1
SM0
SCK1
SCK0
SIOST
SIOSF
0E3H
SIOR
0EAH
IENH
INT0E
INT1E
INT2E
INT3E
-
-
SIOE
T0E
0EBH
IENL
T1E
T2E
T3E
-
ADCE
WDTE
WTE
BITE
0ECH
IRQH
INT0IF
INT1IF
INT2IF
INT3IF
-
-
SIOIF
T0IF
0EDH
IRQL
T1IF
T2IF
T3IF
T4IF
ADCIF
WDTIF
WTIF
BITIF
SIO Data Shift Register
Table 8-2 Control Register Function Description
August 18, 2009 Ver 1.02
www.DataSheet.in
31
MC80F0704/0708/0804/0808
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0EEH
IEDS
IED3H
IED3L
IED2H
IED2L
IED1H
IED1L
IED0H
IED0L
0EFH
ADCM
ADEN
ADCK
ADS3
ADS2
ADS1
ADS0
ADST
ADSF
0F0H
ADCRH
PSSEL1
PSSEL0
ADC8
-
-
-
0F1H
ADCRL
ADC Result Register Low
BITR1
Basic Interval Timer Data Register
WDTON
BTCL
BTS2
BTS1
BTS0
0F2H
0F4H
CKCTLR1
ADRST
WDTR
WDTCL
-
RCWDT
ADC Result Reg. High
7-bit Watchdog Timer Register
WDTDR
Watchdog Timer Data Register (Counter Register)
0F5H
SSCR
Stop & Sleep Mode Control Register
0F7H
PFDR
-
-
-
-
-
PFDEN
PFDM
PFDS
0F8H
PSR0
PWM3O
PWM1O
EC1E
EC0E
INT3E
INT2E
INT1E
INT0E
0F9H
PSR1
-
-
-
-
XTEN
BUZO
T2O
T0O
0FCH
PU0
R0 Pull-up Selection Register
0FDH
PU1
R1 Pull-up Selection Register
0FEH
PU2
R2 Pull-up Selection Register
0FFH
PU3
R3 Pull-up Selection Register
Table 8-2 Control Register Function Description
1. The register BITR and CKCTLR are located at same address. Address ECH is read as BITR, written to CKCTLR.
Caution) The registers of dark-shaded area can not be accessed by bit manipulation instruction such as " SET1, CLR1 " , but should be
accessed by register operation instruction such as " LDM dp,#imm " .
32
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
8.4 Addressing Mode
The MC8 series MCU uses six addressing modes;
Direct Page Addressing → dp
• Register addressing
In this mode, a address is specified within direct page.
• Immediate addressing
Example; G=0
• Direct page addressing
C535
LDA
;A ←RAM[35H]
35H
• Absolute addressing
• Indexed addressing
• Register-indirect addressing
35H
data
➋
~
~
~
~
Register Addressing
0E550H
C5
Register addressing accesses the A, X, Y, C and PSW.
0E551H
data → A
➊
35
Immediate Addressing → #imm
In this mode, second byte (operand) is accessed as a data immediately.
Example:
Absolute Addressing → !abs
0435
ADC
#35H
Absolute addressing sets corresponding memory data to Data, i.e.
second byte (Operand I) of command becomes lower level address and third byte (Operand II) becomes upper level address.
With 3 bytes command, it is possible to access to whole memory
area.
MEMORY
04
A+35H+C → A
35
ADC, AND, CMP, CMPX, CMPY, EOR, LDA, LDX, LDY, OR,
SBC, STA, STX, STY
Example;
0735F0
When G-flag is 1, then RAM address is defined by 16-bit address
which is composed of 8-bit RAM paging register (RPR) and 8-bit
immediate data.
LDM
~
~
35H,#55H
0F100H
➊
~
~
E4
0F101H
55
0F102H
A+data+C → A
35
F0
address: 0F035
data ← 55H
data
0F100H
➊
07
0F102H
~
~
➋
~
~
0F101H
0135H
;A ←ROM[0F035H]
!0F035H
data
0F035H
Example: G=1
E45535
ADC
➋
The operation within data memory (RAM)
ASL, BIT, DEC, INC, LSR, ROL, ROR
Example; Addressing accesses the address 0135H regardless of
G-flag.
35
August 18, 2009 Ver 1.02
www.DataSheet.in
33
MC80F0704/0708/0804/0808
983501
INC
;A ←ROM[135H]
!0135H
35H
data
135H
➌
~
~
~
~
0F100H
98
0F101H
35
0F102H
➋
data
~
~
~
~
➋
data+1 → data
data → A
➊
36H → X
DB
01
➊
address: 0135
X indexed direct page (8 bit offset) → dp+X
Indexed Addressing
This address value is the second byte (Operand) of command plus
the data of X-register. And it assigns the memory in Direct page.
X indexed direct page (no offset) → {X}
In this mode, a address is specified by the X register.
ADC, AND, CMP, EOR, LDA, LDY, OR, SBC, STA STY,
XMA, ASL, DEC, INC, LSR, ROL, ROR
ADC, AND, CMP, EOR, LDA, OR, SBC, STA, XMA
Example; G=0, X=0F5H
Example; X=15H, G=1
C645
D4
LDA
{X}
LDA
;ACC←RAM[X].
3AH
115H
data
~
~
data
➌
➋
~
~
45H+X
~
~
data → A
➊
➋
~
~
0E550H
C6
0E551H
45
data → A
➊
45H+0F5H=13AH
D4
0E550H
X indexed direct page, auto increment→ {X}+
Y indexed direct page (8 bit offset) → dp+Y
In this mode, a address is specified within direct page by the X
register and the content of X is increased by 1.
This address value is the second byte (Operand) of command plus
the data of Y-register, which assigns Memory in Direct page.
LDA, STA
This is same with above (2). Use Y register instead of X.
Example; G=0, X=35H
DB
LDA
{X}+
Y indexed absolute → !abs+Y
Sets the value of 16-bit absolute address plus Y-register data as
Memory.This addressing mode can specify memory in whole area.
Example; Y=55H
34
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
D500FA
LDA
!0FA00H+Y
1625
ADC
[25H+X]
35H
D5
0F101H
00
➊
0F102H
FA
05
36H
0F100H
E0
0FA00H+55H=0FA55H
~
~
~
~
data
0FA55H
➋
~ ➋ 0E005H
~
~
~
0E005H
➊ 25 + X(10) = 35H
data
~
~
~
~
data → A
➌
0FA00H
16
25
➌ A + data + C → A
Indirect Addressing
Y indexed indirect → [dp]+Y
Direct page indirect → [dp]
Assigns data address to use for accomplishing command which
sets memory data (or pair memory) by Operand.
Also index can be used with Index register X,Y.
ADC, AND, CMP, EOR, LDA, OR, SBC, STA
JMP, CALL
Example; G=0, Y=10H
Example; G=0
3F35
Processes memory data as Data, assigned by the data [dp+1][dp]
of 16-bit pair memory paired by Operand in Direct page plus Yregister data.
JMP
1725
[35H]
ADC
[25H]+Y
35H
0A
25H
05
36H
E3
26H
E0
~
~
0E30AH
~
~
➊
NEXT
~
~
0FA00H
➋
~
~
jump to
address 0E30AH
3F
~
~
0E015H
~
~
➋
~
~
0FA00H
35
➊
0E005H + Y(10)
= 0E015H
data
~
~
17
25
➌
A + data + C → A
X indexed indirect → [dp+X]
Absolute indirect → [!abs]
Processes memory data as Data, assigned by 16-bit pair memory
which is determined by pair data [dp+X+1][dp+X] Operand plus
X-register data in Direct page.
The program jumps to address specified by 16-bit absolute address.
ADC, AND, CMP, EOR, LDA, OR, SBC, STA
JMP
Example; G=0, X=10H
Example; G=0
August 18, 2009 Ver 1.02
www.DataSheet.in
35
MC80F0704/0708/0804/0808
1F25E0
JMP
[!0C025H]
PROGRAM MEMORY
0E025H
25
0E026H
E7
~
~
➊
0E725H
~
~
NEXT
~
~
0FA00H
➋
jump to
address 0E30AH
~
~
1F
25
E0
36
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
9. I/O PORTS
The MC80F0704/0708/0804/0808 has three ports (R0, R1 and
R3). These ports pins may be multiplexed with an alternate function for the peripheral features on the device. All port can drive
maximum 20mA of high current in output low state, so it can directly drive LED device.
All pins have data direction registers which can define these ports
as output or input. A “1” in the port direction register configure
the corresponding port pin as output. Conversely, write “0” to the
corresponding bit to specify it as input pin. For example, to use
the even numbered bit of R0 as output ports and the odd numbered bits as input ports, write “55H” to address 0C1H (R0 port
direction register) during initial setting as shown in Figure 9-1 .
WRITE “55H” TO PORT R0 DIRECTION REGISTER
0C0H
R0 data
0C1H
R0 direction
0C2H
R1 direction
BIT
R1 data
0C3H
0 1 0 1 0 1 0 1
7 6 5 4 3 2 1 0
I O I O I O I O PORT
7 6 5 4 3 2 1 0
I: INPUT PORT
O: OUTPUT PORT
Figure 9-1 Example of port I/O assignment
All the port direction registers in the MC80F0704/0708/0804/
0808 have 0 written to them by reset function. On the other hand,
its initial status is input.
9.1 R0 and R0IO register
R0 is an 8-bit CMOS bidirectional I/O port (address 0C0H). Each
I/O pin can independently used as an input or an output through
the R0IO register (address 0C1H). When R00 through R07 pins
are used as input ports, an on-chip pull-up resistor can be connect-
ADDRESS: 0F8H
RESET VALUE: 0000 0000B
ADDRESS: 0C0H
RESET VALUE: 00H
R0 Data Register
R0
ed to them in 1-bit units with a pull-up selection register 0 (PU0).
Each I/O pin of R0 port can be used to open drain output port by
setting the corresponding bit of the open drain selection register
0 (R0OD).
R07 R06 R05 R04 R03 R02 R01 R00
PSR0
PWM3OE PWM1OE EC1E EC0E INT3E INT2E INT1E INT0E
Input / Output data
Port / INT Selection
0: R11, R12, R03, R00
1: INT0, INT1,INT2, INT3
ADDRESS: 0C1H
RESET VALUE: 00H
R0 Direction Register
R0IO
Port / EC Selection
0: R04, R07
1: EC0, EC1
Port Direction
0: Input
1: Output
R0 Pull-up
Selection Register
Port / PWM Selection
0: R10, R11
1: PWM1O, PWM3O
ADDRESS: 0FCH
RESET VALUE: 00H
ADDRESS: 0F9H
RESET VALUE: ---- 0000B
PU0
Pull-up Resister Selection
0: Disable
1: Enable
R0 Open Drain
Selection Register
PSR1
-
-
-
-
AVREFS BUZOE T2OE T0OE
Port / TO Selection
0: R04, R07
1: EC0, EC1
ADDRESS: 0C8H
RESET VALUE: 00H
R12/BUZO Selection
0: R12 port (Turn off buzzer)
1: BUZO port (Turn on buzzer)
R0OD
R10 / AVREF Selection
0: R10 port
1: AVREF port
Open Drain Resister Selection
0: Disable
1: Enable
Figure 9-2 R0 Port Register
In addition, Port R0 is multiplexed with various alternate functions. The port selection register PSR0 (address 0F8H) and PSR1
(address 0F9H) control the selection of alternate functions such as
August 18, 2009 Ver 1.02
www.DataSheet.in
external interrupt 3 (INT3), external interrupt 2 (INT2), event
counter input 0 (EC0), timer 0 output (T0O), timer 2 output
(T2O) and event counter input 1 (EC1). When the alternate func-
37
MC80F0704/0708/0804/0808
tion is selected by writing “1” in the corresponding bit of PSR0
or PSR1, port pin can be used as a corresponding alternate features regardless of the direction register R0IO.
The ADC input channel 1~7 (AN1~AN7) and SIO data input
(SI), SIO data output (SOUT), SIO clock input/output (SCK) can
be selected by setting ADCM(00EFH) and SIOM(00E2H) register
to enable the corresponding peripheral operation and select operation mode.
Port Pin
R00R01
R02
R03
R04
R05
R06
R07
Alternate Function
INT3 (External interrupt 3)
SCK (SIO clock input/output)
AN1(ADC Input channel 1)
SI (SIO data input)
AN2 (ADC Input channel 2)
SOUT (SIO data output)
AN3 (ADC Input channel 3)
INT2 (External interrupt 2)
AN4 (ADC Input channel 4)
EC0 (Event counter input 0)
AN5 (ADC Input channel 5)
T0O (Timer output 0)
AN6 (ADC Input channel 6)
T2O (Timer output 2)
AN7 (ADC Input channel 7)
EC1 (Event counter input 1)
9.2 R1 and R1IO register
R1 is a 5-bit CMOS bidirectional I/O port (address 0C2H). Each
I/O pin can independently used as an input or an output through
the R1IO register (address 0C3H). When R10 through R17 pins
are used as input ports, an on-chip pull-up resistor can be connected to them in 1-bit units with a pull-up selection register 1 (PU1).
Each I/O pin of R1 port can be used to open drain output port by
setting the corresponding bit of the open drain selection register
1 (R1OD).
In addition, Port R1 is multiplexed with various alternate functions. The port selection register PSR0 (address 0F8H) and PSR1
(address 0F9H) control the selection of alternate functions such as
Analog reference voltage input (AVREF), external interrupt 0
(INT0), external interrupt 1 (INT1), PWM 1 output (PWM1O),
PWM 3 output (PWM3O) and buzzer output (BUZO). When the
alternate function is selected by writing “1” in the corresponding
bit of PSR0 or PSR1, port pin can be used as a corresponding alternate features regardless of the direction register R1IO.
lect channel 0 and channel 8 .
Port Pin
R10
R11
R12
R13
R14
R15
R16
R17
Alternate Function
AN0 (ADC input channel 0)
AVREF (Analog reference voltage)
PWM1O (PWM 1 output)
INT0 (External Interrupt 0)
PWM3O (PWM 3 output)
INT1 (External Interrupt 1)
BUZO (Buzzer output)
AN8
The ADC input channel 0 (AN0) and channel 8(AN8) can be selected by setting ADCM(00EFH) register to enable ADC and se-
38
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
ADDRESS: 0C2H
RESET VALUE: 00H
R1 Data Register
R1
R17 R16 R15 R14 R13 R12 R11 R10
ADDRESS: 0F8H
RESET VALUE: 0000 0000B
PSR0 PWM3OEPWM1OE
EC1E EC0E INT3E INT2E INT1E INT0E
Port / INT Selection
0: R11, R12, R03, R00
1: INT0, INT1,INT2, INT3
Input / Output data
ADDRESS: 0C3H
RESET VALUE: 00H
R1 Direction Register
Port / EC Selection
0: R04, R07
1: EC0, EC1
R1IO
Port / PWM Selection
0: R10, R11
1: PWM1O, PWM3O
Port Direction
0: Input
1: Output
R1 Pull-up
Selection Register
ADDRESS: 0FDH
RESET VALUE: 00H
PU1
ADDRESS: 0F9H
RESET VALUE: ---- 0000B
PSR1
Pull-up Resister Selection
0: Disable
1: Enable
R1 Open Drain
Selection Register
ADDRESS: 0C9H
RESET VALUE: 00H
R1OD
Open Drain Resister Selection
0: Disable
1: Enable
-
-
-
-
AVREFS BUZOE T2OE T0OE
Port / TO Selection
0: R05, R06
1: T00, T2O
R12/BUZO Selection
0: R12 port (Turn off buzzer)
1: BUZO port (Turn on buzzer)
R10 / AVREF Selection
0: R10 port
1: AVREF port
Figure 9-3 R1 Port Register
August 18, 2009 Ver 1.02
www.DataSheet.in
39
MC80F0704/0708/0804/0808
9.3 R2 and R2IO register
R2 is an 8-bit CMOS bidirectional I/O port (address 0C4H). Each
I/O pin can independently used as an input or an output through
the R3IO register (address 0C5H). When R20 through R27 pins
are used as input ports, an on-chip pull-up resistor can be connected to them in 1-bit units with a pull-up selection register 2 (PU2).
R20 through R27 pins can be used to open drain output port by
setting the corresponding bit of the open drain selection register
2 (R2OD).
In addition, Port R2 is multiplexed with alternate functions. R23
R24,R25,and R26 can be used as ADC input channel 9 to 12 by
setting ADCM to enable ADC and select channel 9 to 12.
ADDRESS: 0C4H
RESET VALUE: 00H
R2 Data Register
R2
R27 R26 R25 R24 R23 R22 R21 R20
Input / Output data
R2 Direction Register
ADDRESS: 0C5H
RESET VALUE: 00H
R2IO
Port Pin
Alternate Function
R20
R21
R22
R23
R24
R25
R26
R27
AN9 (ADC input channel 9)
AN10 (ADC input channel 10)
AN11 (ADC input channel 11)
AN12 (ADC input channel 12)
-
Port Direction
0: Input
1: Output
R2 Pull-up
Selection Register
ADDRESS: 0FEH
RESET VALUE: 00H
PU2
Pull-up Resister Selection
0: Disable
1: Enable
R2 Open Drain
Selection Register
ADDRESS: 0CAH
RESET VALUE: 00H
R2OD
Open Drain Resister Selection
0: Disable
1: Enable
40
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
9.4 R3 and R3IO register
R3 is a 6-bit CMOS bidirectional I/O port (address 0C6H). Each
I/O pin (except R35) can independently used as an input or an
output through the R3IO register (address 0C7H). R35 is an input
only port. When R30 through R35 pins are used as input ports, an
on-chip pull-up resistor can be connected to them in 1-bit units
with a pull-up selection register 3 (PU3). R30 through R34 pins
can be used to open drain output port by setting the corresponding
bit of the open drain selection register 1 (R3OD).
In addition, Port R3 is multiplexed with alternate functions. R30
R31,and R32 can be used as ADC input channel 13,14 and 15 by
setting ADCM to enable ADC and select channel 13,14 and 15.
R3
R30
R31
R32
-
-
R35 R34 R33 R32 R31 R30
Input data
R3 Direction Register
R3IO
Port Pin
ADDRESS: 0C6H
RESET VALUE: 00H
R3 Data Register
-
-
Input / Output data
ADDRESS: 0C7H
RESET VALUE: 00H
-
Alternate Function
AN13 (ADC input channel 13)
AN14 (ADC input channel 14)
AN15 (ADC input channel 15)
R33, R34 and R35 is multiplexed with XIN, XOUT, and RESET
pin.
Port Direction
0: Input
1: Output
R3 Pull-up
Selection Register
PU3
-
ADDRESS: 0FDH
RESET VALUE: 00H
-
Pull-up Resister Selection
0: Disable
1: Enable
R3 Open Drain
Selection Register
ADDRESS: 0CBH
RESET VALUE: ---0 000-B
R3OD
Open Drain Resister Selection
0: Disable
1: Enable
August 18, 2009 Ver 1.02
www.DataSheet.in
41
MC80F0704/0708/0804/0808
10. CLOCK GENERATOR
As shown in Figure 10-1 , the clock generator produces the basic
clock pulses which provide the system clock to be supplied to the
CPU and the peripheral hardware. It contains main-frequency
clock oscillator. The system clock operation can be easily obtained by attaching a crystal or a ceramic resonator between the
XIN and XOUT pin, respectively. The system clock can also be obtained from the external oscillator. In this case, it is necessary to
input a external clock signal to the XIN pin and open the XOUT
pin. There are no requirements on the duty cycle of the external
clock signal, since the input to the internal clocking circuitry is
through a divide-by-two flip-flop, but minimum and maximum
high and low times specified on the data sheet must be observed.
To the peripheral block, the clock among the not-divided original
clock, clocks divided by 1, 2, 4,..., up to 4096 can be provided.
Peripheral clock is enabled or disabled by STOP instruction. The
peripheral clock is controlled by clock control register
(CKCTLR). See " 11. BASIC INTERVAL TIMER " on page 44
for details.
STOP
INOSC
XIN
OSC
Circuit
XOUT
SLEEP
INOSC
Main OSC
Stop
fXIN
ONP
Circuit
Clock Pulse
Generator
(÷2)
fEX
MUX
INCLK
Int OSC
Circuit
INOSC
PRESCALER
PS0
INOSC (IN4MCLK/IN2MCLK/
IN4MCLKXO/IN2MCLKXO)
7~3
÷1
2~0
PS1
÷2
PS2
÷4
PS3
÷8
PS4
÷16
Configuration Option Register (20FFH)
fEX (Hz)
4M
PS0
Internal
system clock
PS5
÷32
PS6
÷64
PS7
÷128
PS8
÷256
PS9
PS10
PS11
PS12
÷512 ÷1024 ÷2048 ÷4096
Peripheral clock
PS1
PS2
PS3
PS4
PS5
PS6
PS7
PS8
PS9
PS10
PS11
PS12
Frequency
4M
2M
1M
500K
250K
125K
62.5K
31.25K
15.63K
7.183K
3.906K
1.953K
976
period
250n
500n
1u
2u
4u
8u
16u
32u
64u
128u
256u
512u
1.024m
Figure 10-1 Block Diagram of Clock Generator
10.1 Oscillation Circuit
XIN and XOUT are the input and output, respectively, a inverting
amplifier which can be set for use as an on-chip oscillator, as
C1
Xout
shown in Figure 10-2 .
Recommendation
Crystal/Ceramic Oscillator
C2
Xin
Vss
C1,C2 = 10~30pF
Cautions 1. The recommended load capacitor values(C1,C2,C3,C4) are common value
but may not be appropriate for some crystal or ceramic resonator.
Figure 10-2 Oscillator Connections
Note: When using a system clock oscillator, carry out wiring in
the broken line area in Figure 10-2 to prevent any effects from wir-
42
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
ing capacities.
- Minimize the wiring length.
- Do not allow wiring to intersect with other signal conductors.
- Do not allow wiring to come near changing high current.
- Set the potential of the grounding position of the oscillator capacitor to that of VSS. Do not ground to any ground pattern where high
current is present.
- Do not fetch signals from the oscillator.
The user needs to take into account variation due to tolerance of
external R and C components used.
Figure 10-1 shows how the RC combination is connected to the
MC80F0704/0708/0804/0808. External capacitor (CEXT) can be
omitted for more cost saving. However, the characteristics of external R only oscillation are more variable than external RC oscillation.
n addition, see Figure 10-3 for the layout of the crystal.
Vdd
REXT
XIN
CEXT
XOUT
XIN
Cint ≈ 6pF
XOUT
fXIN÷4
Figure 10-1 RC Oscillator Connections
VDD
Figure 10-3 Layout of Oscillator PCB circuit
To drive the device from an external clock source, Xout should
be left unconnected while Xin is driven as shown in Figure 10-4
. There are no requirements on the duty cycle of the external clock
signal, since the input to the internal clocking circuitry is through
a divide-by-two flip-flop, but minimum and maximum high and
low times specified on the data sheet must be observed.
Oscillation circuit is designed to be used either with a ceramic
resonator or crystal oscillator. Since each crystal and ceramic resonator have their own characteristics, the user should consult the
crystal manufacturer for appropriate values of external components.
OPEN
External
Clock
Source
Xout
Xin
Vss
Figure 10-4 External Clock Connections
In addition, the MC80F0704/0708/0804/0808 has an ability for
the external RC oscillated operation. It offers additional cost savings for timing insensitive applications. The RC oscillator frequency is a function of the supply voltage, the external resistor
(REXT) and capacitor (CEXT) values, and the operating temperature.
August 18, 2009 Ver 1.02
www.DataSheet.in
REXT
XIN
CINT ≈ 6pF
fXIN÷4
XOUT
Figure 10-2 R Oscillator Connections
To use the RC oscillation, the CLK option of the configuration
bits (20FFH) should be set to “EXRC or EXRCXO”.
The oscillator frequency, divided by 4, is output from the Xout
pin, and can be used for test purpose or to synchronize other logic.
In addition to external crystal/resonator and external RC/R oscillation, the MC80F0704/0708/0804/0808 provides the internal
4MHz or 2MHz oscillation. The internal 4MHz/2MHz oscillation
needs no external parts.
To use the internal 4MHz/2MHz oscillation, the CLK option of
the configuration bits should be set to “IN4MCLK”,
“IN2MCLK”, “IN4MCLKXO” or “IN2MCLKXO”. For detail
description on the configuration bits, refer to " 22.. Device Configuration Area " on page 100
43
MC80F0704/0708/0804/0808
11. BASIC INTERVAL TIMER
The MC80F0704/0708/0804/0808 has one 8-bit Basic Interval
Timer that is free-run and can not stop. Block diagram is shown
in Figure 11-1 . In addition, the Basic Interval Timer generates
the time base for watchdog timer counting. It also provides a Basic interval timer interrupt (BITIF).
If the STOP instruction executed after writing " 1 " to bit RCWDT
of CKCTLR, it goes into the internal RC oscillated watchdog timer mode. In this mode, all of the block is halted except the internal
RC oscillator, Basic Interval Timer and Watchdog Timer. More
detail informations are explained in Power Saving Function. The
bit WDTON decides Watchdog Timer or the normal 7-bit timer.
Source clock can be selected by lower 3 bits of CKCTLR.
The 8-bit Basic interval timer register (BITR) is increased every
internal count pulse which is divided by prescaler. Since prescaler has divided ratio by 8 to 1024, the count rate is 1/8 to 1/1024
of the oscillator frequency. As the count overflow from FFH to
00H, this overflow causes the interrupt to be generated.
BITR and CKCTLR are located at same address, and address
0F2H is read as a BITR, and written to CKCTLR.
Note: All control bits of Basic interval timer are in CKCTLR reg-
The Basic Interval Timer is controlled by the clock control register (CKCTLR) shown in Figure 11-2. If the RCWDT bit is set to
“1”, the clock source of the BITR is changed to the internal RC
oscillation.
ister which is located at same address of BITR (address ECH). Address ECH is read as BITR, written to CKCTLR. Therefore, the
CKCTLR can not be accessed by bit manipulation instruction.
When write " 1 " to bit BTCL of CKCTLR, BITR register is
cleared to " 0 " and restart to count-up. The bit BTCL becomes " 0 "
after one machine cycle by hardware.
Internal RC OSC
XIN PIN
Prescaler
RCWDT
÷8
÷16
÷32
÷64
÷128
÷256
÷512
÷1024
1
source
clock
8-bit up-counter
overflow
BITR
Basic Interval
Timer Interrupt
BITIF
0
MUX
[0F2H]
To Watchdog timer (WDTCK)
clear
Select Input clock 3
BCK[2:0]
[0F2H]
RCWDT
BTCL
CKCTLR
Basic Interval Timer
clock control register
Read
Internal bus line
Figure 11-1 Block Diagram of Basic Interval Timer
44
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
CKCTLR
[2:0]
Interrupt (overflow) Period (ms)
@ fXIN = 8MHz
Source clock
fXIN÷8
fXIN÷16
fXIN÷32
fXIN÷64
fXIN÷128
fXIN÷256
fXIN÷512
fXIN÷1024
000
001
010
011
100
101
110
111
0.256
0.512
1.024
2.048
4.096
8.192
16.384
32.768
Table 11-1 Basic Interval Timer Interrupt Period
7
CKCTLR
6
-
ADRST
5
4
3
RCWDT WDTONBTCL
BTCL
2
1
0
BTS2 BTS1 BTS0
ADDRESS: 0F2H
INITIAL VALUE: 0-01 0111B
Basic Interval Timer source clock select
000: fXIN ÷ 8
001: fXIN ÷ 16
010: fXIN ÷ 32
011: fXIN ÷ 64
100: fXIN ÷ 128
101: fXIN ÷ 256
110: fXIN ÷ 512
111: fXIN ÷ 1024
Caution:
Both register are in same address,
when write, to be a CKCTLR,
when read, to be a BITR.
Clear bit
0: Normal operation (free-run)
1: Clear 8-bit counter (BITR) to “0”. This bit becomes 0 automatically
after one machine cycle, and starts counting.
Watchdog timer Enable bit
0: Operate as 7-bit Timer
1: Enable Watchdog Timer operation
See the section “Watchdog Timer”.
RC Watchdog Selection bit
0: Disable Internal RC Watchdog Timer
1: Enable Internal RC Watchdog Timer
Address Trap Reset Selection
0: Enable Address Fail Reset
1: Disable Address Fail Reset
7
6
BITR
5
4
3
BTCL
2
1
0
ADDRESS: 0F2H
INITIAL VALUE: Undefined
8-BIT FREE-RUN BINARY COUNTER
Figure 11-2 BITR: Basic Interval Timer Mode Register
Example 1:
Example 2:
Interrupt request flag is generated every 8.192ms at 4MHz.
Interrupt request flag is generated every 8.192ms at 8MHz.
:
LDM
SET1
EI
:
CKCTLR,#1BH
BITE
August 18, 2009 Ver 1.02
www.DataSheet.in
:
LDM
SET1
EI
:
CKCTLR,#1CH
BITE
45
MC80F0704/0708/0804/0808
12. WATCHDOG TIMER
The watchdog timer rapidly detects the CPU malfunction such as
endless looping caused by noise or the like, and resumes the CPU
to the normal state. The watchdog timer signal for detecting malfunction can be selected either a reset CPU or a interrupt request.
RCWDT as shown below.
LDM
LDM
LDM
STOP
NOP
NOP
:
When the watchdog timer is not being used for malfunction detection, it can be used as a timer to generate an interrupt at fixed
intervals.
The watchdog timer has two types of clock source. The first type
is an on-chip RC oscillator which does not require any external
components. This RC oscillator is separate from the external oscillator of the XIN pin. It means that the watchdog timer will run,
even if the clock on the XIN pin of the device has been stopped,
for example, by entering the STOP mode. The other type is a
prescaled system clock.
CKCTLR,#3FH; enable the RC-OSC WDT
WDTR,#0FFH ; set the WDT period
SSCR, #5AH ;ready for STOP mode
; enter the STOP mode
; RC-OSC WDT running
The RC-WDT oscillation period is vary with temperature, VDD
and process variations from part to part (approximately,
33~100uS). The following equation shows the RCWDT oscillated watchdog timer time-out.
TRCWDT=CLKRCWDT×28×WDTR + (CLKRCWDT×28)/2
The watchdog timer consists of 7-bit binary counter and the
watchdog timer data register. When the value of 7-bit binary
counter is equal to the lower 7 bits of WDTR, the interrupt request flag is generated. This can be used as Watchdog timer interrupt or reset the CPU in accordance with the bit WDTON.
where, CLKRCWDT = 33~100uS
In addition, this watchdog timer can be used as a simple 7-bit timer by interrupt WDTIF. The interval of watchdog timer interrupt
is decided by Basic Interval Timer. Interval equation is as below.
TWDT = (WDTR+1) × Interval of BIT
Note: Because the watchdog timer counter is enabled after clearing Basic Interval Timer, after the bit WDTON set to " 1 " , maximum
error of timer is depend on prescaler ratio of Basic Interval Timer.
The 7-bit binary counter is cleared by setting WDTCL(bit7 of
WDTR) and the WDTCL is cleared automatically after 1 machine
cycle.
The RC oscillated watchdog timer is activated by setting the bit
clear
BASIC INTERVAL TIMER
OVERFLOW
Watchdog
Counter (7-bit)
Count
source
clear
“0”
“1”
enable
comparator
WDTCL
WDTON in CKCTLR [0F2H]
7-bit compare data
WDTIF
7
WDTR
[0F4H]
to reset CPU
Watchdog Timer interrupt
Watchdog Timer
Register
Internal bus line
Figure 12-1 Block Diagram of Watchdog Timer
Watchdog Timer Control
watchdog timer is automatically disabled after reset.
Figure 12-2 shows the watchdog timer control register. The
The CPU malfunction is detected during setting of the detection
46
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
low to reset the internal hardware. When WDTON=0, a watchdog
timer interrupt (WDTIF) is generated. The WDTON bit is in register CLKCTLR.
time, selecting of output, and clearing of the binary counter.
Clearing the binary counter is repeated within the detection time.
If the malfunction occurs for any cause, the watchdog timer output will become active at the rising overflow from the binary
counters unless the binary counter is cleared. At this time, when
WDTON=1, a reset is generated, which drives the RESET pin to
W
7
WDTR
W
6
W
5
W
4
W
3
The watchdog timer temporarily stops counting in the STOP
mode, and when the STOP mode is released, it automatically restarts (continues counting).
W
2
W
1
W
0
ADDRESS: 0F4H
INITIAL VALUE: 0111 1111B
WDTCL
7-bit compare data
Clear count flag
0: Free-run count
1: When the WDTCL is set to “1”, binary counter
is cleared to “0”. And the WDTCL becomes “0” automatically
after one machine cycle. Counter count up again.
Figure 12-2 WDTR: Watchdog Timer Control Register
Example: Sets the watchdog timer detection time to 1 sec. at
LDM
LDM
4.194304MHz
CKCTLR,#3FH ;Select 1/1024 clock source, WDTON ← 1, Clear Counter
WDTR,#08FH
LDM
WDTR,#08FH ;Clear counter
:
:
Within WDT
:
detection time
:
LDM
WDTR,#08FH ;Clear counter
:
:
Within WDT
:
detection time
:
LDM
WDTR,#08FH ;Clear counter
Enable and Disable Watchdog
Watchdog Timer Interrupt
Watchdog timer is enabled by setting WDTON (bit 4 in
CKCTLR) to “1”. WDTON is initialized to “0” during reset and
it should be set to “1” to operate after reset is released.
The watchdog timer can be also used as a simple 7-bit timer by
clearing bit4 of CKCTLR to “0”. The interval of watchdog timer
interrupt is decided by Basic Interval Timer. Interval equation is
shown as below.
Example: Enables watchdog timer for Reset
:
LDM
:
:
TWDT = (WDTR+1) × Interval of BIT
CKCTLR,#xxx1_xxxxB;WDTON ← 1
The watchdog timer is disabled by clearing bit 4 (WDTON) of
CKCTLR. The watchdog timer is halted in STOP mode and restarts automatically after STOP mode is released.
The stack pointer (SP) should be initialized before using the
watchdog timer output as an interrupt source.
Example: 7-bit timer interrupt set up.
LDM
LDM
CKCTLR,#xxx0_xxxxB;WDTON ←0
WDTR,#8FH
;WDTCL ←1
:
August 18, 2009 Ver 1.02
www.DataSheet.in
47
MC80F0704/0708/0804/0808
Source clock
BIT overflow
Binary-counter
2
1
3
0
1
2
3
Counter
Clear
WDTR
0
Counter
Clear
3
n
Match
Detect
WDTIF interrupt
WDTR ← “1000_0011B”
WDT reset
reset
Figure 12-3 Watchdog timer Timing
If the watchdog timer output becomes active, a reset is generated,
which drives the RESET pin low to reset the internal hardware.
set is generated in sub clock mode.
The main clock oscillator also turns on when a watchdog timer re-
48
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
13. TIMER/EVENT COUNTER
The MC80F0704/0708/0804/0808 has Four Timer/Counter registers. Each module can generate an interrupt to indicate that an
event has occurred (i.e. timer match).
counter function. When external clock edge input, the count register is captured into Timer data register correspondingly. When
external clock edge input, the count register is captured into capture data register CDRx.
Timer 0 and Timer 1 are can be used either two 8-bit Timer/
Counter or one 16-bit Timer/Counter with combine them. Also
Timer 2 and Timer 3 are same. Timer 4 is 16-bit Timer/Counter.
Timer 0 and Timer 1 is shared with " PWM " function and " Compare output " function. It has six operating modes: " 8-bit timer/
counter " , " 16-bit timer/counter " , " 8-bit capture " , " 16-bit capture " , " 8-bit compare output " , and " 10-bit PWM " which are selected by bit in Timer mode register TM0 and TM1 as shown in
Table 13-1, Figure 13-1 .
In the “timer” function, the register is increased every internal
clock input. Thus, one can think of it as counting internal clock
input. Since a least clock consists of 2 and most clock consists of
2048 oscillator periods, the count rate is 1/2 to 1/2048 of the oscillator frequency.
Timer 2 and Timer 3 is shared with " PWM " function and " Compare output " function. It has six operating modes: " 8-bit timer/
counter " , " 16-bit timer/counter " , " 8-bit capture " , " 16-bit capture " , " 8-bit compare output " , and " 10-bit PWM " which are selected by bit in Timer mode register TM2 and TM3 as shown in
Table 13-2, Figure 13-2 .
In the “counter” function, the register is increased in response to
a 0-to-1 (rising edge) transition at its corresponding external input
pin, EC0 or EC1.
In addition the “capture” function, the register is increased in response external or internal clock sources same with timer or
16BIT
CAP0
CAP1
PWM1E
T0CK
[2:0]
T1CK
[1:0]
PWM1O
0
0
0
0
XXX
XX
0
8-bit Timer
8-bit Timer
0
0
1
0
111
XX
0
8-bit Event counter
8-bit Capture
0
1
0
0
XXX
XX
1
8-bit Capture (internal clock)
8-bit Compare Output
0
X
0
1
XXX
XX
1
8-bit Timer/Counter
10-bit PWM
1
0
0
0
XXX
11
0
16-bit Timer
1
0
0
0
111
11
0
16-bit Event counter
1
1
1
0
XXX
11
0
16-bit Capture (internal clock)
TIMER 0
TIMER 1
Table 13-1 Operation Modes of Timer 0, 1
1. X means the value of “0” or “1” corresponds to user operation.
16BIT
CAP2
CAP3
PWM3E
T2CK
[2:0]
T3CK
[1:0]
PWM3O
0
0
0
0
XXX
XX
0
8-bit Timer
8-bit Timer
0
0
1
0
111
XX
0
8-bit Event counter
8-bit Capture
0
1
0
0
XXX
XX
1
8-bit Capture (internal clock)
8-bit Compare Output
0
X
0
1
XXX
XX
1
8-bit Timer/Counter
10-bit PWM
1
0
0
0
XXX
11
0
16-bit Timer
1
0
0
0
111
11
0
16-bit Event counter
1
1
1
0
XXX
11
0
16-bit Capture (internal clock)
TIMER 2
TIMER 3
Table 13-2 Operating Modes of Timer 2, 3
August 18, 2009 Ver 1.02
www.DataSheet.in
49
MC80F0704/0708/0804/0808
R/W
5
TM0
-
-
R/W
4
R/W
3
R/W
2
R/W
1
R/W
0
CAP0 T0CK2 T0CK1 T0CK0 T0CN
BTCL
T0ST
ADDRESS: 0D0H
INITIAL VALUE: --00 0000B
Bit Name
Bit Position
Description
CAP0
TM0.5
0: Timer/Counter mode
1: Capture mode selection flag
T0CK2
T0CK1
T0CK0
TM0.4
TM0.3
TM0.2
000: 8-bit Timer, Clock source is fXIN ÷ 2
001: 8-bit Timer, Clock source is fXIN ÷ 4
010: 8-bit Timer, Clock source is fXIN ÷ 8
011: 8-bit Timer, Clock source is fXIN ÷ 32
100: 8-bit Timer, Clock source is fXIN ÷ 128
101: 8-bit Timer, Clock source is fXIN ÷ 512
110: 8-bit Timer, Clock source is fXIN ÷ 2048
111: EC0 (External clock)
T0CN
TM0.1
0: Timer count pause
1: Timer count start
T0ST
TM0.0
0: When cleared, stop the counting.
1: When set, Timer 0 Count Register is cleared and start again.
R/W
7
TM1
R/W
6
R/W
5
R/W
4
R/W
3
R/W
2
R/W
1
R/W
0
POL
16BIT PWM1E CAP1 T1CK1 T1CK0 T1CN T1ST
BTCL
ADDRESS: 0D2H
INITIAL VALUE: 00H
Bit Name
Bit Position
Description
POL
TM1.7
0: PWM Duty Active Low
1: PWM Duty Active High
16BIT
TM1.6
0: 8-bit Mode
1: 16-bit Mode
PWM1E
TM1.5
0: Disable PWM
1: Enable PWM
CAP1
TM1.4
0: Timer/Counter mode
1: Capture mode selection flag
T1CK1
T1CK0
TM1.3
TM1.2
00: 8-bit Timer, Clock source is fXIN
01: 8-bit Timer, Clock source is fXIN ÷ 2
10: 8-bit Timer, Clock source is fXIN ÷ 8
11: 8-bit Timer, Clock source is Using the Timer 0 Clock
T1CN
TM1.1
0: Timer count pause
1: Timer count start
T1ST
TM1.0
0: When cleared, stop the counting.
1: When set, Timer 0 Count Register is cleared and start again.
TDR0
TDR1
R/W R/W R/W R/W R/W R/W R/W R/W
7
6
5
4
3
2
1
0
R/W R/W R/W R/W R/W R/W R/W R/W
7
6
5
4
3
2
1
0
ADDRESS: 0D1H
INITIAL VALUE: 0FFH
ADDRESS: 0D3H
INITIAL VALUE: 0FFH
Read: Count value read
Write: Compare data write
Figure 13-1 TM0, TM1 Registers
50
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
R/W
5
TM2
-
-
R/W
4
R/W
3
R/W
2
R/W
1
R/W
0
CAP2 T2CK2 T2CK1 T2CK0 T2CN
BTCL
T2ST
ADDRESS: 0D6H
INITIAL VALUE: --00 0000B
Bit Name
Bit Position
Description
CAP2
TM2.5
0: Timer/Counter mode
1: Capture mode selection flag
T2CK2
T2CK1
T2CK0
TM2.4
TM2.3
TM2.2
000: 8-bit Timer, Clock source is fXIN ÷ 2
001: 8-bit Timer, Clock source is fXIN ÷ 4
010: 8-bit Timer, Clock source is fXIN ÷ 8
011: 8-bit Timer, Clock source is fXIN ÷ 16
100: 8-bit Timer, Clock source is fXIN ÷ 64
101: 8-bit Timer, Clock source is fXIN ÷ 256
110: 8-bit Timer, Clock source is fXIN ÷ 1024
111: EC1 (External clock)
T2CN
TM2.1
0: Timer count pause
1: Timer count start
T2ST
TM2.0
0: When cleared, stop the counting.
1: When set, Timer 0 Count Register is cleared and start again.
R/W
7
TM3
POL
R/W
6
R/W
5
R/W
4
R/W
3
R/W
2
R/W
1
R/W
0
16BIT PWM3E CAP3 T3CK1 T3CK0 T3CN T3ST
BTCL
ADDRESS: 0D8H
INITIAL VALUE: 00H
Bit Name
Bit Position
Description
POL
TM3.7
0: PWM Duty Active Low
1: PWM Duty Active High
16BIT
TM3.6
0: 8-bit Mode
1: 16-bit Mode
PWM3E
TM3.5
0: Disable PWM
1: Enable PWM
CAP3
TM3.4
0: Timer/Counter mode
1: Capture mode selection flag
T3CK1
T3CK0
TM3.3
TM3.2
00: 8-bit Timer, Clock source is fXIN
01: 8-bit Timer, Clock source is fXIN ÷ 4
10: 8-bit Timer, Clock source is fXIN ÷ 16
11: 8-bit Timer, Clock source is Using the Timer 2 Clock
T3CN
TM3.1
0: Timer count pause
1: Timer count start
T3ST
TM3.0
0: When cleared, stop the counting.
1: When set, Timer 0 Count Register is cleared and start again.
TDR2
TDR3
R/W R/W R/W R/W R/W R/W R/W R/W
7
6
5
4
3
2
1
0
R/W R/W R/W R/W R/W R/W R/W R/W
7
6
5
4
3
2
1
0
ADDRESS: 0D7H
INITIAL VALUE: 0FFH
ADDRESS: 0D9H
INITIAL VALUE: 0FFH
Read: Count value read
Write: Compare data write
Figure 13-2 TM2, TM3 Registers
August 18, 2009 Ver 1.02
www.DataSheet.in
51
MC80F0704/0708/0804/0808
13.1 8-bit Timer / Counter Mode
The MC80F0704/0708/0804/0808 has four 8-bit Timer/
Counters, Timer 0, Timer 1, Timer 2, Timer 3. The Timer 0, Timer 1 are shown in Figure 13-3 and Timer 2, Timer 3 are shown in
Figure 13-4 .
PWM3E of TM1 or TM3 should be cleared to " 0 " (Figure 13-3 ).
These timers have each 8-bit count register and data register. The
count register is increased by every internal or external clock input. The internal clock has a prescaler divide ratio option of 1, 2,
4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048 or external clock (selected by control bits TxCK0, TxCK1, TxCK2 of register TMx).
The “timer” or “counter” function is selected by control registers
TM0, TM1, TM2, TM3 as shown in Figure 13-1 . To use as an 8bit timer/counter mode, bit CAP0, CAP1, CAP2, or CAP3 of
TMx should be cleared to “0” and 16BIT and PWM1E or
7
6
-
-
-
TM0
5
-
4
3
2
1
0
ADDRESS: 0D0H
INITIAL VALUE: --00 0000B
CAP0 T0CK2 T0CK1 T0CK0 T0CN T0ST
BTCL
0
X
X
X
X
X
X means don’t care
7
TM1
6
5
4
3
2
1
0
POL 16BIT PWM1E CAP1 T1CK1 T1CK0 T1CN T1ST
BTCL
X
0
0
0
X
X
X
ADDRESS: 0D2H
INITIAL VALUE: 00H
X
X means don’t care
T0CK[2:0]
EDGE
DETECTOR
EC0 PIN
111
T0ST
÷2
000
XIN PIN
Prescaler
÷4
0: Stop
1: Clear and start
001
÷8
010
÷ 32
T0 (8-bit)
clear
011
÷ 128
100
÷ 512
÷ 2048
101
T0CN
T0IF
Comparator
110
MUX
TIMER 0
TDR0 (8-bit)
TIMER 0
INTERRUPT
F/F
R05 / T0O
T1CK[1:0]
T1ST
÷1
÷2
÷8
0: Stop
1: Clear and start
11
00
T1 (8-bit)
01
clear
10
MUX
T1CN
T1IF
Comparator
TIMER 1
TIMER 1
INTERRUPT
TDR1 (8-bit)
Figure 13-3 8-bit Timer/Counter 0, 1
52
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
7
6
-
-
-
TM2
5
-
4
3
2
1
0
ADDRESS: 0D6H
INITIAL VALUE: --000000B
CAP2 T2CK2 T2CK1 T2CK0 T2CN T2ST
BTCL
0
X
X
X
X
X
X means don’t care
7
TM3
6
5
4
3
2
1
0
ADDRESS: 0D8H
INITIAL VALUE: 00H
POL 16BIT PWM3E CAP3 T3CK1 T3CK0 T3CN T3ST
BTCL
X
0
0
0
X
X
X
X
X means don’t care
T2CK[2:0]
EDGE
DETECTOR
EC1 PIN
111
T2ST
÷2
000
XIN PIN
Prescaler
÷4
0: Stop
1: Clear and start
001
÷8
010
÷ 16
T2 (8-bit)
clear
011
÷ 64
100
÷ 256
÷ 1024
101
T2CN
T2IF
Comparator
110
MUX
TIMER 2
TDR2 (8-bit)
TIMER 2
INTERRUPT
F/F
R06 / T2O
T3CK[1:0]
T3ST
÷1
÷4
÷ 16
0: Stop
1: Clear and start
11
00
T3 (8-bit)
01
clear
10
MUX
T3CN
T3IF
Comparator
TIMER 3
TIMER 3
INTERRUPT
TDR3 (8-bit)
Figure 13-4 8-bit Timer/Counter 2, 3
August 18, 2009 Ver 1.02
www.DataSheet.in
53
MC80F0704/0708/0804/0808
These timers have each 8-bit count register and data register. The
count register is increased by every internal or external clock input. The internal clock has a prescaler divide ratio option of 2, 4,
8, 32, 128, 512, 2048 selected by control bits T0CK[2:0] of register TM0 or 1, 2, 8 selected by control bits T1CK[1:0] of register
TM1, or 2, 4, 8, 16, 64, 256, 1024 selected by control bits
T2CK[2:0] of register TM2, or 1, 4, 16 selected by control bits
T3CK[1:0] of register TM3. In the Timer 0, timer register T0 increases from 00H until it matches TDR0 and then reset to 00H.
The match output of Timer 0 generates Timer 0 interrupt (latched
in T0IF bit).
Example 1:
Timer0 = 2ms 8-bit timer mode at 4MHz
Timer1 = 0.5ms 8-bit timer mode at 4MHz
Timer2 = 1ms 8-bit timer mode at 4MHz
Timer3 = 1ms 8-bit timer mode at 4MHz
LDM
LDM
LDM
LDM
LDM
LDM
LDM
LDM
SET1
SET1
SET1
SET1
EI
TDR0,#249
TDR1,#249
TDR2,#249
TDR3,#249
TM0,#0000_1111B
TM1,#0000_1011B
TM2,#0000_1111B
TM3,#0000_1011B
T0E
T1E
T2E
T3E
In counter function, the counter is increased every 0-to-1 (rising
edge) transition of EC0 pin. In order to use counter function, the
bit EC0 of the Port Selection Register (PSR0.4) is set to " 1 " . The
Timer 0 can be used as a counter by pin EC0 input, but Timer 1
can not. Likewise, In order to use Timer2 as counter function, the
bit EC1 of the Port Selection Register (PSR0.5) is set to " 1 " . The
Timer 2 can be used as a counter by pin EC1 input, but Timer 3
can not.
Example 2:
Timer0 = 8-bit event counter mode
Timer1 = 0.5ms 8-bit timer mode at 4MHz
Timer2 = 8-bit event counter mode
Timer3 = 1ms 8-bit timer mode at 4MHz
LDM
LDM
LDM
LDM
LDM
LDM
LDM
LDM
SET1
SET1
SET1
SET1
EI
8-bit Timer Mode
In the timer mode, the internal clock is used for counting up.
Thus, you can think of it as counting internal clock input. The
contents of TDRn are compared with the contents of up-counter,
Tn. If match is found, a timer n interrupt (TnIF) is generated and
the up-counter is cleared to 0. Counting up is resumed after the
up-counter is cleared.
TDR0,#249
TDR1,#249
TDR2,#249
TDR3,#249
TM0,#0001_1111B
TM1,#0000_1011B
TM2,#0001_1111B
TM3,#0000_1011B
T0E
T1E
T2E
T3E
As the value of TDRn is changeable by software, time interval is
set as you want.
Start count
~
~
Source clock
~
~
Up-counter
n
2
3
~
~
n-2
n-1
n
0
1
2
3
4
Match
Detect
Counter
Clear
~
~
T1IF interrupt
1
~
~
TDR1
0
Figure 13-5 Timer Mode Timing Chart
54
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
Example: Make 1ms interrupt using by Timer0 at 4MHz
LDM
LDM
SET1
EI
TM0,#0FH
TDR0,#124
T0E
;
;
;
;
divide by 32
8us x (124+1)= 1ms
Enable Timer 0 Interrupt
Enable Master Interrupt
When
TM0 = 0000 1111B (8-bit Timer mode, Prescaler divide ratio = 32)
TDR0 = 124D = 7CH
fXIN = 4 MHz
1
INTERRUPT PERIOD =
× 32 × (124+1) = 1 ms
4 × 106 Hz
TDR0
MATCH
(TDR0 = T0)
Count Pulse
Period
7C
7C
8 μs
6
~~
~~
up
-c
ou
nt
~~
7B
7A
5
4
3
2
1
0
0
TIME
Interrupt period
= 8 μs x (124+1)
Timer 0 (T0IF)
Interrupt
Occur interrupt
Occur interrupt
Occur interrupt
Figure 13-6 Timer Count Example
8-bit Event Counter Mode
In order to use event counter function, the bit 4, 5 of the Port Selection Register PSR0(address 0F8H) is required to be set to “1”.
In this mode, counting up is started by an external trigger. This
trigger means rising edge of the EC0 or EC1 pin input. Source
clock is used as an internal clock selected with timer mode register TM0 or TM2. The contents of timer data register TDRn (n =
0,1,2,3) are compared with the contents of the up-counter Tn. If a
match is found, an timer interrupt request flag TnIF is generated,
and the counter is cleared to “0”. The counter is restart and count
up continuously by every rising edge of the EC0 or EC1 pin input.
The maximum frequency applied to the EC0 or EC1 pin is fXIN/
2 [Hz].
After reset, the value of timer data register TDRn is initialized to
" 0 " , The interval period of Timer is calculated as below equation.
1Period (sec) = ---------- × 2 × Divide Ratio × (TDRn+1)
f XIN
~
~
Start count
EC0 pin input
~
~
1
0
2
~
~
Up-counter
n-1
n
0
1
2
~
~
~
~
T1IF interrupt
n
~
~
TDR0
Figure 13-7 Event Counter Mode Timing Chart
August 18, 2009 Ver 1.02
www.DataSheet.in
55
MC80F0704/0708/0804/0808
TDR1
disable
~
~
clear & start
enable
up
-c
ou
nt
stop
~
~
TIME
Timer 1 (T1IF)
Interrupt
Occur interrupt
Occur interrupt
T1ST
Start & Stop
T1CN
Control count
T1ST = 1
T1ST = 0
T1CN = 1
T1CN = 0
Figure 13-8 Count Operation of Timer / Event counter
56
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
13.2 16-bit Timer / Counter Mode
The Timer register is being run with all 16 bits. A 16-bit timer/
counter register T0, T1 are incremented from 0000H until it
matches TDR0, TDR1 and then resets to 0000H. The match output generates Timer 0 interrupt.
The clock source of the Timer 2 is selected either internal or external clock by bit T2CK[2:0]. In 16-bit mode, the bits
T3CK[1:0] and 16BIT of TM3 should be set to " 1 " respectively
as shown in Figure 13-10 .
The clock source of the Timer 0 is selected either internal or external clock by bit T0CK[2:0]. In 16-bit mode, the bits
T1CK[1:0] and 16BIT of TM1 should be set to " 1 " respectively
as shown in Figure 13-9 .
Even if the Timer 0 (including Timer 1) is used as a 16-bit timer,
the Timer 2 and Timer 3 can still be used as either two 8-bit timer
or one 16-bit timer by setting the TM3. Reversely, even if the
Timer 2 (including Timer 3) is used as a 16-bit timer, the Timer
0 and Timer 1 can still be used as 8-bit timer independently.
Likewise, A 16-bit timer/counter register T2, T3 are incremented
from 0000H until it matches TDR2, TDR3 and then resets to
0000H. The match output generates Timer 2 interrupt.
7
6
-
-
-
TM0
5
-
4
3
2
1
0
ADDRESS: 0D0H
INITIAL VALUE: --00 0000B
BTCL
CAP0 T0CK2 T0CK1 T0CK0 T0CN T0ST
0
X
X
X
X
X
X means don’t care
7
TM1
6
5
4
3
2
1
0
ADDRESS: 0D2H
INITIAL VALUE: 00H
POL 16BIT PWM1E CAP1 T1CK1 T1CK0 T1CN T1ST
BTCL
X
1
0
0
1
1
X
X
X means don’t care
T0CK[2:0]
EDGE
DETECTOR
EC0 PIN
111
÷2
÷4
Prescaler
XIN PIN
÷8
÷ 32
÷ 128
÷ 512
÷ 2048
T0ST
0: Stop
1: Clear and start
000
001
T1 + T0
(16-bit)
010
011
100
101
T0CN
T0IF
Comparator
110
MUX
clear
TIMER 0
INTERRUPT
(Not Timer 1 interrupt)
TDR1 + TDR0
(16-bit)
Higher byte Lower byte
COMPARE DATA
TIMER 0 + TIMER 1 → TIMER 0 (16-bit)
Figure 13-9 16-bit Timer/Counter for Timer 0, 1
August 18, 2009 Ver 1.02
www.DataSheet.in
57
MC80F0704/0708/0804/0808
7
6
-
-
-
TM2
5
-
4
3
2
1
0
ADDRESS: 0D6H
INITIAL VALUE: --000000B
CAP2 T2CK2 T2CK1 T2CK0 T2CN T2ST
BTCL
0
X
X
X
X
X
X means don’t care
7
TM3
6
5
4
3
2
1
0
ADDRESS: 0D8H
INITIAL VALUE: 00H
POL 16BIT PWM3E CAP3 T3CK1 T3CK0 T3CN T3ST
BTCL
X
1
0
0
1
1
X
X
X means don’t care
T2CK[2:0]
EDGE
DETECTOR
EC1 PIN
111
÷2
÷4
Prescaler
XIN PIN
÷8
÷ 16
÷ 64
÷ 256
÷ 1024
T2ST
0: Stop
1: Clear and start
000
001
T3 + T2
(16-bit)
010
011
100
101
clear
T2CN
T2IF
Comparator
110
TIMER 2
INTERRUPT
(Not Timer 3 interrupt)
TDR3 + TDR2
(16-bit)
MUX
Higher byte Lower byte
COMPARE DATA
TIMER 2 + TIMER 3 → TIMER 2 (16-bit)
Figure 13-10 16-bit Timer/Counter for Timer 2, 3
13.3 8-bit Compare Output (16-bit)
The MC80F0704/0708/0804/0808 has Timer Compare Output
function. To pulse out, the timer match can goes to port pin (T0O
or T2O) as shown in Figure 13-3 or Figure 13-4 . Thus, pulse out
is generated by the timer match. These operation is implemented
to pin, R05/AN5//T0O or R06/AN6/T2O.
nal having a 50 : 50 duty square wave, and output frequency is
same as below equation.
Oscillation Frequency
f COMP = -----------------------------------------------------------------------------------------2 × Prescaler Value × ( TDR + 1 )
In this mode, the bit T0OE or T2OE bit of Port Selection register1
(PSR1.0 or PSR1.1) should be set to " 1 " . This pin output the sig-
13.4 8-bit Capture Mode
The Timer 0 capture mode is set by bit CAP0 of timer mode register TM0 (bit CAP1 of timer mode register TM1 for Timer 1) as
shown in Figure 13-11 . Likewise, the Timer 2 capture mode is
set by bit CAP2 of timer mode register TM2 (bit CAP3 of timer
mode register TM3 for Timer 3) as shown in Figure 13-12 .
The Timer/Counter register is increased in response internal or
58
www.DataSheet.in
external input. This counting function is same with normal timer
mode, and Timer interrupt is generated when timer register T0
(T1, T2, T3) increases and matches TDR0 (TDR1, TDR2,
TDR3).
This timer interrupt in capture mode is very useful when the pulse
width of captured signal is more wider than the maximum period
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
of Timer.
For example, in Figure 13-14 , the pulse width of captured signal
is wider than the timer data value (FFH) over 2 times. When external interrupt is occurred, the captured value (13H) is more little
than wanted value. It can be obtained correct value by counting
the number of timer overflow occurrence.
Timer/Counter still does the above, but with the added feature
that a edge transition at external input INTx pin causes the current
value in the Timer x register (T0,T1,T2,T3), to be captured into
registers CDRx (CDR0, CDR1, CDR2, CDR3), respectively. Af-
August 18, 2009 Ver 1.02
www.DataSheet.in
ter captured, Timer x register is cleared and restarts by hardware.
It has three transition modes: " falling edge " , " rising edge " , " both
edge " which are selected by interrupt edge selection register
IEDS. Refer to “17.4 External Interrupt” on page 84. In addition,
the transition at INTn pin generate an interrupt.
Note: The CDRn and TDRn are in same address.In the capture
mode, reading operation is read the CDRn, not TDRn because
path is opened to the CDRn.
59
MC80F0704/0708/0804/0808
7
6
-
-
-
TM0
5
-
4
3
2
1
0
ADDRESS: 0D0H
INITIAL VALUE: --00 0000B
CAP0 T0CK2 T0CK1 T0CK0 T0CN T0ST
BTCL
1
X
X
X
X
X
X means don’t care
7
TM1
6
5
4
3
2
1
0
ADDRESS: 0D2H
INITIAL VALUE: 00H
POL 16BIT PWM1E CAP1 T1CK1 T1CK0 T1CN T1ST
BTCL
X
0
0
1
X
X
X
X
X means don’t care
T0CK[2:0]
Edge
Detector
EC0 PIN
111
T0ST
÷2
000
÷4
XIN PIN
÷8
Prescaler
0: Stop
1: Clear and start
001
T0 (8-bit)
010
÷ 32
011
÷ 128
100
÷ 512
÷ 2048
101
clear
T0CN
Capture
110
CDR0 (8-bit)
MUX
IEDS[1:0]
“01”
“10”
INT0 PIN
INT0IF
T1CK[1:0]
INT0
INTERRUPT
“11”
T1ST
÷1
÷2
÷8
0: Stop
1: Clear and start
11
00
T1 (8-bit)
01
clear
10
MUX
T1CN
Capture
CDR1 (8-bit)
IEDS[3:2]
“01”
INT1 PIN
“10”
INT1IF
INT1
INTERRUPT
“11”
Figure 13-11 8-bit Capture Mode for Timer 0, 1
60
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
7
6
-
-
-
TM2
5
-
4
3
2
1
0
ADDRESS: 0D6H
INITIAL VALUE: --00 0000B
CAP2 T2CK2 T2CK1 T2CK0 T2CN T2ST
BTCL
1
X
X
X
X
X
X means don’t care
7
TM3
6
5
4
3
2
1
0
ADDRESS: 0D8H
INITIAL VALUE: 00H
POL 16BIT PWM3E CAP3 T3CK1 T3CK0 T3CN T3ST
BTCL
X
0
0
1
X
X
X
X
X means don’t care
T2CK[2:0]
Edge
Detector
EC1 PIN
111
T2ST
÷2
000
÷4
Prescaler
XIN PIN
0: Stop
1: Clear and start
001
÷8
T2 (8-bit)
010
÷ 16
011
÷ 64
100
÷ 256
÷ 1024
101
clear
T2CN
Capture
110
CDR2 (8-bit)
MUX
IEDS[5:4]
“01”
“10”
INT2 PIN
INT2IF
T3CK[1:0]
INT2
INTERRUPT
“11”
T3ST
÷1
÷4
÷ 16
0: Stop
1: Clear and start
11
00
T3 (8-bit)
01
clear
10
MUX
T3CN
Capture
CDR3 (8-bit)
IEDS[7:6]
“01”
INT3 PIN
“10”
INT3IF
INT3
INTERRUPT
“11”
Figure 13-12 8-bit Capture Mode for Timer 2, 3
August 18, 2009 Ver 1.02
www.DataSheet.in
61
MC80F0704/0708/0804/0808
This value is loaded to CDR0
n
T0
n-1
t
un
~
~
~
~
9
-c
o
8
up
7
6
5
4
~
~
3
2
1
0
TIME
Ext. INT0 Pin
Interrupt Request
( INT0IF )
Interrupt Interval Period
Ext. INT0 Pin
Interrupt Request
( INT0IF )
20nS
Capture
( Timer Stop )
5nS
Delay
Clear & Start
Figure 13-13 Input Capture Operation of Timer 0 Capture mode
Ext. INT0 Pin
Interrupt Request
( INT0IF )
Interrupt Interval Period=01H+FFH +01H+FFH +01H+13H=214H
Interrupt Request
( T0IF )
FFH
FFH
T0
13H
00H
00H
Figure 13-14 Excess Timer Overflow in Capture Mode
62
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
13.5 16-bit Capture Mode
The clock source of the Timer 2 is selected either internal or external clock by bit T2CK[2:0]. In 16-bit mode, the bits
T3CK1,T3CK0, CAP3 and 16BIT of TM3 should be set to " 1 " respectively as shown in Figure 13-16 .
16-bit capture mode is the same as 8-bit capture, except that the
Timer register is being run will 16 bits. The clock source of the
Timer 0 is selected either internal or external clock by bit
T0CK[2:0]. In 16-bit mode, the bits T1CK1, T1CK0, CAP1 and
16BIT of TM1 should be set to " 1 " respectively as shown in Figure 13-15 .
7
6
-
-
-
TM0
5
-
4
3
2
1
0
ADDRESS: 0D0H
INITIAL VALUE: --00 0000B
CAP0 T0CK2 T0CK1 T0CK0 T0CN T0ST
BTCL
1
X
X
X
X
X
X means don’t care
7
TM1
6
5
4
3
2
1
0
ADDRESS: 0D2H
INITIAL VALUE: 00H
POL 16BIT PWM1E CAP1 T1CK1 T1CK0 T1CN T1ST
BTCL
X
1
0
1
1
1
X
X
X means don’t care
T0CK[2:0]
Edge
Detector
EC0 PIN
111
T0ST
÷2
÷4
Prescaler
XIN PIN
÷8
÷ 32
÷ 128
÷ 512
÷ 2048
0: Stop
1: Clear and start
000
001
TDR1 + TDR0
(16-bit)
010
011
100
clear
T0CN
101
Capture
110
CDR1 + CDR0
(16-bit)
MUX
IEDS[1:0]
Higher byte Lower byte
CAPTURE DATA
“01”
INT0 PIN
“10”
INT0IF
INT0
INTERRUPT
“11”
Figure 13-15 16-bit Capture Mode of Timer 0, 1
August 18, 2009 Ver 1.02
www.DataSheet.in
63
MC80F0704/0708/0804/0808
7
6
-
-
-
TM2
5
-
4
3
2
1
0
ADDRESS: 0D6H
INITIAL VALUE: --00 0000B
CAP2 T2CK2 T2CK1 T2CK0 T2CN T2ST
BTCL
1
X
X
X
X
X
X means don’t care
7
TM3
6
5
4
3
2
1
0
ADDRESS: 0D8H
INITIAL VALUE: 00H
POL 16BIT PWM3E CAP3 T3CK1 T3CK0 T3CN T3ST
BTCL
X
1
0
1
1
1
X
X
X means don’t care
T2CK[2:0]
Edge
Detector
EC1 PIN
111
T2ST
÷2
÷4
Prescaler
XIN PIN
÷8
÷ 16
÷ 64
÷ 256
÷ 1024
0: Stop
1: Clear and start
000
001
TDR3 + TDR2
(16-bit)
010
011
clear
100
T2CN
101
Capture
110
CDR3 + CDR2
(16-bit)
MUX
IEDS[5:4]
Higher byte Lower byte
CAPTURE DATA
“01”
“10”
INT2 PIN
INT2IF
INT2
INTERRUPT
“11”
Figure 13-16 16-bit Capture Mode of Timer 2, 3
Example 1:
Example 3:
Timer0 = 16-bit timer mode, 0.5s at 4MHz
Timer0 = 16-bit capture mode
LDM
LDM
LDM
LDM
SET1
EI
:
:
TM0,#0000_1111B;8uS
TM1,#0100_1100B;16bit Mode
TDR0,# & lt; 62499
;8uS X 62500
TDR1,# & gt; 62499
;=0.5s
T0E
Example 2:
LDM
LDM
LDM
LDM
LDM
LDM
SET1
EI
:
:
PSR0,#0000_0001B;INT0 set
TM0,#0010_1111B;Capture Mode
TM1,#0100_1100B;16bit Mode
TDR0,# & lt; 0FFH
;
TDR1,# & gt; 0FFH
;
IEDS,#01H;Falling Edge
T0E
Timer0 = 16-bit event counter mode
LDM
LDM
LDM
LDM
LDM
SET1
EI
:
:
64
www.DataSheet.in
PSR0,#0001_0000B;EC0 Set
TM0,#0001_1111B;Counter Mode
TM1,#0100_1100B;16bit Mode
TDR0,# & lt; 0FFH
;
TDR1,# & gt; 0FFH
;
T0E
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
13.6 PWM Mode
The MC80F0704/0708/0804/0808 has high speed PWM (Pulse
Width Modulation) functions which shared with Timer1 or
Timer3.
resolution.
Frequency
In PWM mode, R10 / PWM1O or R11 / PWM3O pin output up
to a 10-bit resolution PWM output. These pins should be configured as a PWM output by setting " 1 " bit PWM1OE and
PWM3OE in PSR0 register.
Resolution
T1CK[1:0]
= 00(250nS)
T1CK[1:0]
= 01(500nS)
T1CK[1:0]
= 10(2uS)
10-bit
3.9kHz
0.98kHz
0.49kHz
The period of the PWM1 output is determined by the T1PPR (T1
PWM Period Register) and T1PWHR[3:2] (bit3,2 of T1 PWM
High Register) and the duty of the PWM output is determined by
the T1PDR (T1 PWM Duty Register) and T3PWHR[1:0] (bit1,0
of T1 PWM High Register).
9-bit
7.8kHz
1.95kHz
0.97kHz
8-bit
15.6kHz
3.90kHz
1.95kHz
7-bit
31.2kHz
7.81kHz
3.90kHz
The period of the PWM3 output is determined by the T3PPR (T3
PWM Period Register) and T3PWHR[3:2] (bit3,2 of T3 PWM
High Register) and the duty of the PWM output is determined by
the T3PDR (T3 PWM Duty Register) and T3PWHR[1:0] (bit1,0
of T3 PWM High Register).
The user writes the lower 8-bit period value to the T1(3)PPR and
the higher 2-bit period value to the T1(3)PWHR[3:2]. And writes
duty value to the T1(3)PDR and the T1(3)PWHR[1:0] same way.
The T1(3)PDR is configured as a double buffering for glitchless
PWM output. In Figure 13-18 , the duty data is transferred from
the master to the slave when the period data matched to the counted value. (i.e. at the beginning of next duty cycle)
Table 13-3 PWM Frequency vs. Resolution at 4MHz
The bit POL of TM1 or TM3 decides the polarity of duty cycle.
If the duty value is set same to the period value, the PWM output
is determined by the bit POL (1: High, 0: Low). And if the duty
value is set to " 00H " , the PWM output is determined by the bit
POL (1: Low, 0: High).
It can be changed duty value when the PWM output. However the
changed duty value is output after the current period is over. And
it can be maintained the duty value at present output when
changed only period value shown as Figure 13-20 . As it were, the
absolute duty time is not changed in varying frequency. But the
changed period value must greater than the duty value.
PWM1(3) Period = [PWM1(3)HR[3:2]T(2)3PPR] X
Source Clock
Note: If changing the Timer1 to PWM function, it should be stop
PWM1(3) Duty = [PWM1(3)HR[1:0]T3PDR] X Source
Clock
the timer clock firstly, and then set period and duty register value.
If user writes register values while timer is in operation, these register could be set with certain values.
Ex) Sample Program @4MHz 2uS
The relation of frequency and resolution is in inverse proportion.
Table 13-3 shows the relation of PWM frequency vs. resolution.
If it needed more higher frequency of PWM, it should be reduced
August 18, 2009 Ver 1.02
www.DataSheet.in
LDM
LDM
LDM
LDM
LDM
TM1,#1010_1000b ; Set Clock & PWM3E
T1PPR,#199
; Period :400uS=2uSX(199+1)
T1PDR,#99
; Duty:200uS=2uSX(99+1)
PWM1HR,00H
TM1,#1010_1011b ; Start timer1
65
MC80F0704/0708/0804/0808
R/W
7
TM1
R/W
6
R/W
5
R/W
4
R/W
3
R/W
2
R/W
1
R/W
0
ADDRESS: 0D2H
INITIAL VALUE: 00H
POL 16BIT PWM1E CAP3 T3CK1 T3CK0 T3CN T3ST
BTCL
X
1
0
X
X
X
X
7
6
5
4
W
3
W
2
W
1
W
0
-
-
-
-
-
T1PWHR
0
-
-
-
X:The value " 0 " or " 1 " corresponding your operation.
ADDRESS: 0D5H
INITIAL VALUE: ---- 0000B
T3PWHR3 T3PWHR2 T3PWHR1 T3PWHR0
BTCL
X
X
X
Bit Manipulation Not Available
X
X:The value " 0 " or " 1 " corresponding your operation.
Period High
W
7
W
6
W
5
W
4
T1PPR
W
3
Duty High
W
2
W
1
W
0
R/W
2
R/W
1
R/W
0
ADDRESS: 0D3H
INITIAL VALUE: 0FFH
BTCL
R/W
7
R/W
6
R/W
5
R/W
4
T1PDR
R/W
3
ADDRESS: 0D4H
INITIAL VALUE: 00H
BTCL
T1PWHR[1:0]
T0 clock source
[T0CK]
T1CK[1:0]
0 : Stop
1 : Clear and Start
Prescaler
XIN PIN
÷2
÷8
Clear
00
R10 / PWM1O PIN
R
2-bit
01
T1(8-bit)
10
MUX
S Q
Comparator
11
÷1
PWM1OE
[PSR0.6]
T1PPR(8-bit)
T1ST
POL
T1CN
Comparator
Slave
T1PDR(8-bit)
T1PWHR[1:0]
Master
T1PDR(8-bit)
Figure 13-17 PWM1 Mode
66
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
R/W
7
TM3
R/W
6
R/W
5
R/W
4
R/W
3
R/W
2
R/W
1
R/W
0
ADDRESS: 0D8H
INITIAL VALUE: 00H
POL 16BIT PWM3E CAP3 T3CK1 T3CK0 T3CN T3ST
BTCL
X
1
0
X
X
X
X
7
6
5
4
W
3
W
2
W
1
W
0
-
-
-
-
-
T3PWHR
0
-
-
-
X:The value " 0 " or " 1 " corresponding your operation.
ADDRESS: 0DBH
INITIAL VALUE: ---- 0000B
T3PWHR3 T3PWHR2 T3PWHR1 T3PWHR0
BTCL
X
X
X
Bit Manipulation Not Available
X
X:The value " 0 " or " 1 " corresponding your operation.
Period High
W
7
W
6
W
5
W
4
T3PPR
W
3
Duty High
W
2
W
1
W
0
R/W
2
R/W
1
R/W
0
ADDRESS: 0D9H
INITIAL VALUE: 0FFH
BTCL
R/W
7
R/W
6
R/W
5
R/W
4
T3PDR
R/W
3
ADDRESS: 0DAH
INITIAL VALUE: 00H
BTCL
T3PWHR[1:0]
T2 clock source
[T2CK]
T3CK[1:0]
0 : Stop
1 : Clear and Start
Prescaler
XIN PIN
÷4
÷ 16
Clear
00
R
2-bit
01
R11 / PWM3O PIN
T3(8-bit)
10
MUX
S Q
Comparator
11
÷1
PWM3O
[PSR0.7]
T3PPR(8-bit)
T3ST
POL
T3CN
Comparator
Slave
T3PDR(8-bit)
T3PWHR[1:0]
Master
T3PDR(8-bit)
Figure 13-18 PWM3 Mode
August 18, 2009 Ver 1.02
www.DataSheet.in
67
MC80F0704/0708/0804/0808
~
~
~
~
Source
clock
01
02
03
04
PWM1E
7E
7F
~ ~
~ ~
00
~ ~ ~
~ ~ ~
T1
80
3FF
00
01
02
~
~
T1ST
~
~
T1CN
~
~
PWM1O
[POL=1]
~
~
~
~
~
~
PWM1O
[POL=0]
Duty Cycle [ (1+7Fh) x 250nS = 32uS ]
Period Cycle [ (3FFh+1) x 250nS = 256uS, 3.9KHz ]
T1CK[1:0] = 00 ( XIN )
T1PWHR = 0CH
Period
T1PWHR3
1
T1PWHR2
T1PPR (8-bit)
1
FFH
T1PWHR0
T1PDR (8-bit)
0
7FH
T1PPR = FFH
T1PDR = 7FH
Duty
T1PWHR1
0
Figure 13-19 Example of PWM1 at 4MHz
T1CK[1:0] = 10 ( 1us )
PWM1HR = 00H
T1PPR = 0DH
Write T1PPR to 09H
T1PDR = 04H
Source
clock
T1
00 01 02 03 04 05 06 07 08
09 0A 0B 0C 0D
00 01 02 03 04 05 06 07 08 09
00 01 02 03
04
PWM1O
POL=1
Duty Cycle
[ (04h+1) x 2uS = 10uS ]
Period Cycle [ (1+0Dh) x 2uS = 28uS, 35.5KHz ]
Duty Cycle
[ (04h+1) x 2uS = 10uS ]
Duty Cycle
[ (04h+1) x 2uS = 10uS ]
Period Cycle [ (1+09h) x 2uS = 20uS, 50KHz ]
Figure 13-20 Example of Changing the PWM1 Period in Absolute Duty Cycle (@4MHz)
68
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
14. ANALOG TO DIGITAL CONVERTER
The analog-to-digital converter (A/D) allows conversion of an
analog input signal to a corresponding 10-bit digital value. The A/
D module has sixteen analog inputs, which are multiplexed into
one sample and hold. The output of the sample and hold is the input into the converter, which generates the result via successive
approximation.
set to “1”. After one cycle, it is cleared by hardware. The register
ADCRH and ADCRL contains the results of the A/D conversion.
When the conversion is completed, the result is loaded into the
ADCRH and ADCRL, the A/D conversion status bit ADSF is set
to “1”, and the A/D interrupt flag ADCIF is set. See Figure 14-1
for operation flow.
The analog reference voltage is selected to VDD or AVref by setting of the bit AVREFS in PSR1 register. If external analog reference AVref is selected, the analog input channel 0 (AN0)
should not be selected to use. Because this pin is used to an analog
reference of A/D converter.
The block diagram of the A/D module is shown in Figure 14-3 .
The A/D status bit ADSF is set automatically when A/D conversion is completed, cleared when A/D conversion is in process.
The conversion time takes 13 times of conversion source clock.
The conversion source clock should selected for the conversion
time being more than 25μs.
The A/D module has three registers which are the control register
ADCM and A/D result register ADCRH and ADCRL. The ADCRH[7:6] is used as ADC clock source selection bits too. The
register ADCM, shown in Figure 14-4 , controls the operation of
the A/D converter module. The port pins can be configured as analog inputs or digital I/O.
It is selected for the corresponding channel to be converted by
setting ADS[3:0]. The A/D port is set to analog input port by
ADEN and ADS[3:0] regardless of port I/O direction register.
The port unselected by ADS[3:0] operates as normal port.
A/D Converter Cautions
(1) Input range of AN0 ~ AN15
The input voltage of A/D input pins should be within the specification range. In particular, if a voltage above VDD (or AVref) or
below VSS is input (even if within the absolute maximum rating
range), the conversion value for that channel can not be indeterminate. The conversion values of the other channels may also be
affected.
(2) Noise countermeasures
In order to maintain 10-bit resolution, attention must be paid to
noise on pins VDD (or AVref) and analog input pins (AN0 ~
AN15). Since the effect increases in proportion to the output impedance of the analog input source, it is recommended in some
cases that a capacitor be connected externally as shown in Figure
14-2 in order to reduce noise. The capacitance is user-selectable
and appropriately determined according to the target system.
Enable A/D Converter
A/D Input Channel Select
Conversion Source Clock Select
Analog
Input
A/D Start (ADST = 1)
AN0~AN15
0~1000pF
User Selectable
NOP
Figure 14-2 Analog Input Pin Connecting Capacitor
ADSF = 1
NO
YES
Read ADCR
Figure 14-1 A/D Converter Operation Flow
How to Use A/D Converter
The processing of conversion is start when the start bit ADST is
August 18, 2009 Ver 1.02
www.DataSheet.in
(3) I/O operation
The analog input pins AN0 ~ AN15 also have function as input/
output port pins. When A/D conversion is performed with any
pin, be sure not to execute a PORT input instruction with the selected pin while conversion is in progress, as this may reduce the
conversion resolution.
Also, if digital pulses are applied to a pin adjacent to the pin in the
process of A/D conversion, the expected A/D conversion value
69
MC80F0704/0708/0804/0808
may not be obtainable due to coupling noise. Therefore, avoid applying pulses to pins adjacent to the pin undergoing A/D conversion.
ply voltage error
Note: If the AVREF voltage is less than VDD voltage and anlalog input pins(ANX), shared with various alternate function, are used bidirectional I/O port, the leakage current
may flow VDD pin to AVREF pin in output high mode or anlalog input pins(ANX) to AVREF pin in input high mode.
(4) AVDD pin input impedance
A series resistor string of approximately 5KΩ is connected between the AVREF pin and the VSS pin. Therefore, if the output impedance of the analog power source is high, this will result in
parallel connection to the series resistor string between the
AVREF pin and the VSS pin, and there will be a large analog sup-
AVREFS (PSR1.3)
ADEN
0
VDD
Resistor Ladder Circuit
1
AN0 / AVREF
AN1
Successive
MUX
ADC
INTERRUPT
ADCIF
Approximation
Circuit
Sample & Hold
AN14
ADC8
AN15
0
1
10-bit Mode
8-bit Mode
ADS[3:0] (ADCM[5:2])
98
98
32
10-bit ADCR
ADCRADCR
10-bit (10-bit)
0 0
ADCRH
ADCRL (8-bit)
1 0
ADC Result Register
ADCRH
ADCRL (8-bit)
1 0
ADC Result Register
Figure 14-3 A/D Block Diagram
70
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
R/W R/W R/W
R
3
2
1
0
ADS1
ADEN ADCK ADS3 ADS2 BTCL ADS0 ADST ADSF
R/W
7
ADCM
R/W
6
R/W
5
R/W
4
ADDRESS: 0EFH
INITIAL VALUE: 0000 0001B
A/D status bit
0: A/D conversion is in progress
1: A/D conversion is completed
A/D start bit
Setting this bit starts an A/D conversion.
After one cycle, bit is cleared to “0” by hardware.
Analog input channel select
0000: Channel 0 (AN0) 0110: Channel 6 (AN6)
0001: Channel 1 (AN1) 0111: Channel 7 (AN7)
0010: Channel 2 (AN2) 1000: Channel 8 (AN8)
0011: Channel 3 (AN3) 1001: Channel 9 (AN9)
0100: Channel 4 (AN4) 1010: Channel 10 (AN10)
0101: Channel 5 (AN5) 1011: Channel 11 (AN11)
1100: Channel 12 (AN12)
1101: Channel 13 (AN13)
1110: Channel 14 (AN14)
1111: Channel 15 (AN15)
A/D converter Clock Source Divide Ratio Selection bit
0: Clock Source fPS
1: Clock Source fPS ÷ 2
~ 1101: Not available
A/D converter Enable bit
0: A/D converter module turn off and current is not flow.
1: Enable A/D converter
W
ADCRH
W
7
6
W
5
PSSEL1 PSSEL0 ADC8
-
-
-
R
R
4
3
BTCL
-
2
1
0
-
-
ADDRESS: 0F0H
INITIAL VALUE: 010- ----B
A/D Conversion High Data
ADC 8-bit Mode select bit
0: 10-bit Mode
1: 8-bit Mode
R
7
R
5
R
6
ADCRL
R
4
R
3
BTCL
R
2
R
1
R
0
A/D Conversion Clock (fPS) Source Selection
00: fXIN ÷ 4
01: fXIN ÷ 8
10: fXIN ÷ 16
11: fXIN ÷ 32
ADDRESS: 0F1H
INITIAL VALUE: Undefined
A/D Conversion Low Data
ADCK
PSSEL1
PSSEL0
PS Clock Selection
0
0
0
PS = fXIN ÷ 4
0
0
1
PS = fXIN ÷ 8
0
0
0
PS = fXIN ÷ 16
0
0
1
PS = fXIN ÷ 32
1
1
0
PS = fXIN ÷ 64
1
1
1
PS = fXIN ÷ 128
1
1
0
PS = fXIN ÷ 256
1
1
1
PS = fXIN ÷ 512
PS : Conversion Clock
Figure 14-4 A/D Converter Control & Result Register
August 18, 2009 Ver 1.02
www.DataSheet.in
71
MC80F0704/0708/0804/0808
15. SERIAL INPUT/OUTPUT (SIO)
The serial Input/Output is used to transmit/receive 8-bit data serially. The Serial Input/Output (SIO) module is a serial interface
useful for communicating with other peripheral of microcontroller devices. These peripheral devices may be serial EEPROMs,
shift registers, display drivers, A/D converters, etc. This SIO is 8bit clock synchronous type and consists of serial I/O data register,
serial I/O mode register, clock selection circuit, octal counter and
control circuit as illustrated in Figure 15-1 . The SO pin is designed to input and output. So the Serial I/O(SIO) can be operated
with minimum two pin. Pin R00/SCK, R01/SI, and R02/SO pins
are controlled by the Serial Mode Register. The contents of the
Serial I/O data register can be written into or read out by software.
The data in the Serial Data Register can be shifted synchronously
with the transfer clock signal.
SIOST
SIOSF
clear
XIN PIN
Prescaler
SCK[1:0]
÷4
÷ 16
POL
Start
00
“0”
10
Timer0
Overflow
01
“1”
Clock
Complete
SIO
CONTROL
CIRCUIT
overflow
Clock
11
SCK PIN
“11”
MUX
Octal
Counter
(3-bit)
SIOIF
Serial communication
Interrupt
not “11”
SCK[1:0]
SM0
SO PIN
IOSW
SOUT
IOSW
1
SI PIN
Input shift register
0
Shift
SIOR
Internal Bus
Figure 15-1 SIO Block Diagram
72
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
Serial I/O Mode Register (SIOM) controls serial I/O function.
According to SCK1 and SCK0, the internal clock or external
clock can be selected.
R/W
7
SIOM
R/W
6
R/W
5
POL IOSW SM1
R/W
4
Serial I/O Data Register (SIOR) is an 8-bit shift register. First
LSB is send or is received first.
R/W R/W R/W R
3
2
1
0
SM0 BTCL SCK0 SIOST SIOSF
SCK1
ADDRESS: 0E2H
INITIAL VALUE: 0000 0001B
Serial transmission status bit
0: Serial transmission is in progress
1: Serial transmission is completed
Serial transmission start bit
Setting this bit starts an Serial transmission.
After one cycle, bit is cleared to “0” by hardware.
Serial transmission Clock selection
00: fXIN ÷ 4
01: fXIN ÷ 16
10: TMR0OV(Timer0 Overflow)
11: External Clock
Serial transmission Operation Mode
00: Normal Port (R00,R01,R02)
01: Sending Mode (SCK,R01,SO)
10: Receiving Mode (SCK,SI,R02)
11: Sending & Receiving Mode (SCK,SI,SO)
Serial Input Pin Selection bit
0: SI Pin Selection
1: SO Pin Selection
Serial Clock Polarity Selection bit
0: Data Transmission at Falling Edge
Received Data Latch at Rising Edge
1: Data Transmission at Rising Edge
Received Data Latch at Falling Edge
SIOR
R/W R/W R/W R/W R/W R/W R/W R/W
7
6
5
4
3
2
1
0
BTCL
ADDRESS: 0E3H
INITIAL VALUE: Undefined
Sending Data at Sending Mode
Receiving Data at Receiving Mode
Figure 15-2 SIO Control Register
15.1 Transmission/Receiving Timing
The serial transmission is started by setting SIOST(bit1 of SIOM)
to “1”. After one cycle of SCK, SIOST and SIOSF (bit 0 of SIOM) is cleared automatically to “0”. At the default state of POL
bit clear, the serial output data from 8-bit shift register is output
at falling edge of SCLK, and input data is latched at rising edge
August 18, 2009 Ver 1.02
www.DataSheet.in
of SCLK pin (Refer to Figure 15-3 ). When transmission clock is
counted 8 times, serial I/O counter is cleared as ‘0”. Transmission
clock is halted in “H” state and serial I/O interrupt (SIOIF) occurred. SIOSF is set to “1” automatically.
73
MC80F0704/0708/0804/0808
SIOST
SCK [R00]
(POL=0)
SO [R02]
D0
D1
D2
D3
D4
D5
D6
D7
SI [R01]
(IOSW=0)
D0
D1
D2
D3
D4
D5
D6
D7
IOSWIN [R02]
(IOSW=1)
D0
D1
D2
D3
D4
D5
D6
D7
SIOIF
(SIO Int. Req)
SIOSF
(SIO Status)
Figure 15-3 Serial I/O Timing Diagram at POL=0
SIOST
SCK [R00]
(POL=1)
SO [R02]
D0
D1
D2
D3
D4
D5
D6
D7
SI [R01]
(IOSW=0)
D0
D1
D2
D3
D4
D5
D6
D7
IOSWIN [R02]
(IOSW=1)
D0
D1
D2
D3
D4
D5
D6
D7
SIOIF
(SIO Int. Req)
SIOSF
(SIO Status)
Figure 15-4 Serial I/O Timing Diagram at POL=1
74
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
15.2 The usage of Serial I/O
1. Select transmission/receiving mode.
2. In case of sending mode, write data to be send to SIOR.
3. Set SIOST to “1” to start serial transmission.
4. The SIO interrupt is generated at the completion of SIO
and SIOIF is set to “1”.
5. In case of receiving mode, the received data is acquired
by reading the SIOR.
6. When using polling method, the completion of 1 byte
serial communication can be checked by reading
SIOST and SIOSF. As shown in example code, wait until SIOST is changed to “0” and then wait the SIOSF is
changed to “1” for completion check.
August 18, 2009 Ver 1.02
www.DataSheet.in
LDM SIOR,#0AAh
;set tx data
LDM SIOM,#0011_1100b;set SIO mode
NOP
LDM SIOM,#0011_1110b;SIO Start
NOP
SIO_WAIT:
NOP
BBS SIOST,SIO_WAIT ;wait first edge
BBC SIOSF,SIO_WAIT ;wait complete
Note: When external clock is used, the frequency should be less
than 1MHz and recommended duty is 50%. If both transmission
mode is selected and transmission is performed simultaneously,
error may be occur.
75
MC80F0704/0708/0804/0808
16. BUZZER FUNCTION
The buzzer driver block consists of 6-bit binary counter, buzzer
register BUZR, and clock source selector. It generates squarewave which has very wide range frequency (488Hz ~ 250kHz at
fXIN= 4MHz) by user software.
driving.
Equation of frequency calculation is shown below.
f XIN
f BUZ = -------------------------------------------------------------------------------2 × DivideRatio × ( BUR + 1 )
A 50% duty pulse can be output to R12 / BUZO pin to use for piezo-electric buzzer drive. Pin R12 is assigned for output port of
Buzzer driver by setting the bit 2 of PSR1(address 0F9H) to “1”.
For PSR1 register, refer to Figure 16-2 .
fBUZ: Buzzer frequency
fXIN: Oscillator frequency
Divide Ratio: Prescaler divide ratio by BUCK[1:0]
BUR: Lower 6-bit value of BUZR. Buzzer period value.
Example: 5kHz output at 4MHz.
LDM
LDM
BUZR,#0011_0001B
PSR1,#XXXX_X1XXB
The frequency of output signal is controlled by the buzzer control
register BUZR. The bit 0 to bit 5 of BUZR determine output frequency for buzzer driving.
X means don’t care
The bit 0 to 5 of BUZR determines output frequency for buzzer
R12 port data
Prescaler
÷8
XIN PIN
6-BIT BINARY
COUNTER
00
÷ 16
01
÷ 32
MUX
0
10
÷ 64
F/F
11
R12/BUZO PIN
1
Comparator
MUX
2
Compare data
BUZO
6
PSR1
BUR
Port selection register 1
[0F9H]
[0E0H]
Internal bus line
Figure 16-1 Block Diagram of Buzzer Driver
ADDRESS: 0E0H
RESET VALUE: 0FFH
W
BUZR
W
W
W
W
W
W
ADDRESS: 0F9H
RESET VALUE: ---- 0000B
W
PSR1
BUCK1 BUCK0
-
-
BUR[5:0]
Buzzer Period Data
Source clock select
00: fXIN ÷ 8
01: fXIN ÷ 16
10: fXIN ÷ 32
11: fXIN ÷ 64
-
-
-
BUZO
-
-
R12 / BUZO Selection
0: R12 port (Turn off buzzer)
1: BUZO port (Turn on buzzer)
Figure 16-2 Buzzer Register & PSR1
76
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
The 6-bit counter is cleared and starts the counting by writing signal at BUZR register. It is incremental from 00H until it matches
6-bit BUR value.
BUR
[5:0]
BUR[7:6]
00
01
10
11
When main-frequency is 4MHz, buzzer frequency is shown as
below Table 16-1.
BUR
[5:0]
BUR[7:6]
00
01
10
11
00
01
02
03
04
05
06
07
250.000
125.000
83.333
62.500
50.000
41.667
35.714
31.250
125.000
62.500
41.667
31.250
25.000
20.833
17.857
15.625
62.500
31.250
20.833
15.625
12.500
10.417
8.929
7.813
31.250
15.625
10.417
7.813
6.250
5.208
4.464
3.906
20
21
22
23
24
25
26
27
7.576
7.353
7.143
6.944
6.757
6.579
6.410
6.250
3.788
3.676
3.571
3.472
3.378
3.289
3.205
3.125
1.894
1.838
1.786
1.736
1.689
1.645
1.603
1.563
0.947
0.919
0.893
0.868
0.845
0.822
0.801
0.781
08
09
0A
0B
0C
0D
0E
0F
27.778
25.000
22.727
20.833
19.231
17.857
16.667
15.625
13.889
12.500
11.364
10.417
9.615
8.929
8.333
7.813
6.944
6.250
5.682
5.208
4.808
4.464
4.167
3.906
3.472
3.125
2.841
2.604
2.404
2.232
2.083
1.953
28
29
2A
2B
2C
2D
2E
2F
6.098
5.952
5.814
5.682
5.556
5.435
5.319
5.208
3.049
2.976
2.907
2.841
2.778
2.717
2.660
2.604
1.524
1.488
1.453
1.420
1.389
1.359
1.330
1.302
0.762
0.744
0.727
0.710
0.694
0.679
0.665
0.651
10
11
12
13
14
15
16
17
14.706
13.889
13.158
12.500
11.905
11.364
10.870
10.417
7.353
6.944
6.579
6.250
5.952
5.682
5.435
5.208
3.676
3.472
3.289
3.125
2.976
2.841
2.717
2.604
1.838
1.736
1.645
1.563
1.488
1.420
1.359
1.302
30
31
32
33
34
35
36
37
5.102
5.000
4.902
4.808
4.717
4.630
4.545
4.464
2.551
2.500
2.451
2.404
2.358
2.315
2.273
2.232
1.276
1.250
1.225
1.202
1.179
1.157
1.136
1.116
0.638
0.625
0.613
0.601
0.590
0.579
0.568
0.558
18
19
1A
1B
1C
1D
1E
1F
10.000
9.615
9.259
8.929
8.621
8.333
8.065
7.813
5.000
4.808
4.630
4.464
4.310
4.167
4.032
3.906
2.500
2.404
2.315
2.232
2.155
2.083
2.016
1.953
1.250
1.202
1.157
1.116
1.078
1.042
1.008
0.977
38
39
3A
3B
3C
3D
3E
3F
4.386
4.310
4.237
4.167
4.098
4.032
3.968
3.907
2.193
2.155
2.119
2.083
2.049
2.016
1.984
1.953
1.096
1.078
1.059
1.042
1.025
1.008
0.992
0.977
0.548
0.539
0.530
0.521
0.512
0.504
0.496
0.488
Table 16-1 buzzer frequency (kHz unit)
August 18, 2009 Ver 1.02
www.DataSheet.in
77
MC80F0704/0708/0804/0808
17. INTERRUPTS
The MC80F0704/0708/0804/0808 interrupt circuits consist of Interrupt enable register (IENH, IENL), Interrupt request flags of
IRQH, IRQL, Priority circuit, and Master enable flag (“I” flag of
PSW). Fifteen interrupt sources are provided. The configuration
of interrupt circuit is shown in Figure 17-1 and interrupt priority
is shown in Table 17-1.
The Timer 0 ~ Timer 3 Interrupts are generated by T0IF, T1IF,
T2IF and T3IF which is set by a match in their respective timer/
counter register.
The Basic Interval Timer Interrupt is generated by BITIF which
is set by an overflow in the timer register.
The AD converter Interrupt is generated by ADCIF which is set
by finishing the analog to digital conversion.
The External Interrupts INT0 ~ INT3 each can be transition-activated (1-to-0 or 0-to-1 transition) by selection IEDS register.
The flags that actually generate these interrupts are bit INT0IF,
INT1IF, INT2IF and INT3IF in register IRQH. When an external
interrupt is generated, the generated flag is cleared by the hardware when the service routine is vectored to only if the interrupt
was transition-activated.
The Watchdog timer is generated by WDTIF and WTIF which is
set by a match in Watchdog timer register.
Internal bus line
[0EAH]
Interrupt Enable
Register (Higher byte)
IENH
IRQH
[0ECH]
INT0IF
INT1IF
INT2
INT2IF
INT3
INT3IF
Serial
Communication
Timer 0
Release STOP/SLEEP
Priority Control
INT0
INT1
I-flag is in PSW, it is cleared by “DI”, set by
“EI” instruction. When it goes interrupt service,
I-flag is cleared by hardware, thus any other
interrupt are inhibited. When interrupt service is
completed by “RETI” instruction, I-flag is set to
“1” by hardware.
SIOIF
T0IF
IRQL
[0EDH]
Timer 1
Interrupt Master
Enable Flag
T2IF
Timer 3
I-flag
T1IF
Timer 2
To CPU
T3IF
A/D Converter
ADCIF
Watchdog Timer
Interrupt
Vector
Address
Generator
WDTIF
BIT
BITIF
[0EBH]
IENL
Interrupt Enable
Register (Lower byte)
Internal bus line
Figure 17-1 Block Diagram of Interrupt
The Basic Interval Timer Interrupt is generated by BITIF which
is set by a overflow in the timer counter register.
78
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
The SIO interrupt is generated by SIOIF which is set by completion of SIO data reception or transmission.
The interrupts are controlled by the interrupt master enable flag
I-flag (bit 2 of PSW on Figure 8-3 ), the interrupt enable register
(IENH, IENL), and the interrupt request flags (in IRQH and
IRQL) except Power-on reset and software BRK interrupt. The
Table 17-1 shows the Interrupt priority.
Vector addresses are shown in Figure 8-6 . Interrupt enable registers are shown in Figure 17-2 . These registers are composed of
interrupt enable flags of each interrupt source and these flags determines whether an interrupt will be accepted or not. When enable flag is “0”, a corresponding interrupt source is prohibited.
Note that PSW contains also a master enable bit, I-flag, which
disables all interrupts at once.
Reset/Interrupt
Hardware Reset
External Interrupt 0
External Interrupt 1
External Interrupt 2
External Interrupt 3
Serial Input/Output
Timer/Counter 0
Timer/Counter 1
Timer/Counter 2
Timer/Counter 3
ADC Interrupt
Watchdog Timer
Basic Interval Timer
Symbol
Priority
RESET
INT0
INT1
INT2
INT3
SIO
Timer 0
Timer 1
Timer 2
Timer 3
ADC
WDT
BIT
1
2
3
4
5
6
7
8
9
10
11
12
13
Table 17-1 Interrupt Priority
August 18, 2009 Ver 1.02
www.DataSheet.in
79
MC80F0704/0708/0804/0808
R/W
IENH
INT0E
R/W
R/W
R/W
INT1E INT2E INT3E
-
-
-
-
R/W
R/W
SIOE
T0E
MSB
ADDRESS: 0EAH
INITIAL VALUE: 0000 --00B
LSB
Timer/Counter 0 interrupt enable flag
Serial Communication interrupt enable flag
External interrupt 3 enable flag
External interrupt 2 enable flag
External interrupt 1 enable flag
External interrupt 0 enable flag
R/W
IENL
R/W
R/W
R/W
T1E
T2E
T3E
-
R/W
R/W
ADCE WDTE
R/W
R/W
-
BITE
LSB
MSB
ADDRESS: 0EBH
INITIAL VALUE: 000- 00-0B
Basic Interval Timer interrupt enable flag
Watchdog timer interrupt enable flag
A/D Converter interrupt enable flag
Timer/Counter 3 interrupt enable flag
Timer/Counter 2 interrupt enable flag
Timer/Counter 1 interrupt enable flag
Figure 17-2 Interrupt Enable Flag Register
R/W
IRQH
R/W
R/W
R/W
INT0IF INT1IF INT2IF INT3IF
-
-
R/W
R/W
-
-
SIOIF
T0IF
MSB
LSB
ADDRESS: 0ECH
INITIAL VALUE: 0000 --00B
Timer/Counter 0 interrupt request flag
Serial Communication interrupt request flag
External interrupt 3 request flag
External interrupt 2 request flag
External interrupt 1 request flag
External interrupt 0 request flag
R/W
IRQL
R/W
R/W
-
T1IF
T2IF
T3IF
-
MSB
R/W
R/W
ADCIF WDTIF
-
R/W
-
BITIF
LSB
ADDRESS: 0EDH
INITIAL VALUE: 000- 00-0B
Basic Interval Timer interrupt request flag
Watchdog timer interrupt request flag
A/D Converter interrupt request flag
Timer/Counter 3 interrupt request flag
Timer/Counter 2 interrupt request flag
Timer/Counter 1 interrupt request flag
80
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
Figure 17-3 Interrupt Request Flag Register
17.1 Interrupt Sequence
An interrupt request is held until the interrupt is accepted or the
interrupt latch is cleared to “0” by a reset or an instruction. Interrupt acceptance sequence requires 8 cycles of fXIN (2μs at fX-
IN =4MHz) after the completion of the current instruction
execution. The interrupt service task is terminated upon execution of an interrupt return instruction [RETI].
Interrupt acceptance
1. The interrupt master enable flag (I-flag) is cleared to
“0” to temporarily disable the acceptance of any following maskable interrupts. When a non-maskable interrupt is accepted, the acceptance of any following
interrupts is temporarily disabled.
2. The contents of the program counter (return address)
and the program status word are saved (pushed) onto the
stack area. The stack pointer decreases 3 times.
3. The entry address of the interrupt service program is
read from the vector table address and the entry address
is loaded to the program counter.
4. The instruction stored at the entry address of the interrupt service program is executed.
System clock
Instruction Fetch
SP
Address Bus
PC
Data Bus
Not used
SP-1
PCH
PCL
SP-2
PSW
V.L.
V.L.
ADL
V.H.
ADH
New PC
OP code
Internal Read
Internal Write
Interrupt Processing Step
Interrupt Service Task
V.L. and V.H. are vector addresses.
ADL and ADH are start addresses of interrupt service routine as vector contents.
Figure 17-4 Timing chart of Interrupt Acceptance and Interrupt Return Instruction
Basic Interval Timer
Vector Table Address
0FFE0H
0FFE1H
012H
0E3H
Entry Address
0E312H
0E313H
0EH
2EH
A interrupt request is not accepted until the I-flag is set to “1”
even if a requested interrupt has higher priority than that of the
current interrupt being serviced.
When nested interrupt service is required, the I-flag should be set
to “1” by “EI” instruction in the interrupt service program. In this
case, acceptable interrupt sources are selectively enabled by the
individual interrupt enable flags.
Correspondence between vector table address for BIT interrupt
and the entry address of the interrupt service program.
Clearing Interrupt Request Flag
The Interrupt Request flag may not cleared itself during interrupt
acceptance processing. After interrupt acceptance, it should be
August 18, 2009 Ver 1.02
www.DataSheet.in
cleared as shown in interrupt service routine.
81
MC80F0704/0708/0804/0808
Note: The MC80F0708 and HMS87C1416B is similar in
function, but the interrupt processing method is different.
When replacing the HMS87C1416B to MC80F0708, clearing interrupt request flag should be added.
Example: Clearing Interrupt Request Flag
T1_INT:
CLR1
T1IF
;CLEAR T1 REQUEST
interrupt processing
RETI
;RETURN
Saving/Restoring General-purpose Register
During interrupt acceptance processing, the program counter and
the program status word are automatically saved on the stack, but
accumulator and other registers are not saved itself. These registers are saved by the software if necessary. Also, when multiple
interrupt services are nested, it is necessary to avoid using the
same data memory area for saving registers.
The following method is used to save/restore the general-purpose
registers.
interrupt processing
POP
POP
POP
RETI
Y
X
A
;RESTORE Y REG.
;RESTORE X REG.
;RESTORE ACC.
;RETURN
General-purpose register save/restore using push and pop instructions;
Example: Register save using push and pop instructions
INTxx:
CLR1
PUSH
PUSH
PUSH
INTxxIF
A
X
Y
;CLEAR REQUEST.
;SAVE ACC.
;SAVE X REG.
;SAVE Y REG.
17.2 BRK Interrupt
Software interrupt can be invoked by BRK instruction, which has
the lowest priority order.
Interrupt vector address of BRK is shared with the vector of
TCALL 0 (Refer to Program Memory Section). When BRK interrupt is generated, B-flag of PSW is set to distinguish BRK from
TCALL 0.
Each processing step is determined by B-flag as shown in Figure
17-5 .
B-FLAG
BRK or
TCALL0
=0
=1
BRK
INTERRUPT
ROUTINE
TCALL0
ROUTINE
RETI
RET
Figure 17-5 Execution of BRK/TCALL0
17.3 Multi Interrupt
If two requests of different priority levels are received simultaneously, the request of higher priority level is serviced. If requests of the interrupt are received at the same time
simultaneously, an internal polling sequence determines by hard-
82
www.DataSheet.in
ware which request is serviced. However, multiple processing
through software for special features is possible. Generally when
an interrupt is accepted, the I-flag is cleared to disable any further
interrupt. But as user sets I-flag in interrupt routine, some further
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
interrupt can be serviced even if certain interrupt is in progress.
Main Program
service
TIMER 1
service
enable INT0
disable other
INT0
service
EI
Occur
TIMER1 interrupt
In this example, the INT0 interrupt can be serviced without any
pending, even TIMER1 is in progress.
Because of re-setting the interrupt enable registers IENH,IENL
and master enable “EI” in the TIMER1 routine.
Occur
INT0
enable INT0
enable other
Figure 17-6 Execution of Multi Interrupt
Example: During Timer1 interrupt is in progress, INT0 interrupt
serviced without any suspend.
TIMER1: CLR1
PUSH
PUSH
PUSH
LDM
LDM
EI
:
:
T1IF
;Clear Timer1 Request
A
X
Y
IENH,#80H
;Enable INT0 only
IENL,#0
;Disable other int.
;Enable Interrupt
August 18, 2009 Ver 1.02
www.DataSheet.in
:
:
:
:
LDM
LDM
POP
POP
POP
RETI
IENH,#0FFH ;Enable all interrupts
IENL,#0FFH
Y
X
A
83
MC80F0704/0708/0804/0808
17.4 External Interrupt
The edge detection of external interrupt has three transition activated mode: rising edge, falling edge, and both edge.
The external interrupt on INT0, INT1, INT2 and INT3 pins are
edge triggered depending on the edge selection register IEDS (address 0EEH) as shown in Figure 17-7 .
01
INT0 pin
10
INT0IF
INT0 INTERRUPT
INT1IF
INT1 INTERRUPT
INT2IF
INT2 INTERRUPT
INT3IF
INT3 INTERRUPT
11
01
INT1 pin
10
11
01
INT2 pin
10
11
01
INT3 pin
10
11
2
2
2
IEDS
2
Edge selection
Register
[0EEH]
Figure 17-7 External Interrupt Block Diagram
INT0 ~ INT3 are multiplexed with general I/O ports (R11, R12,
R03, R00). To use as an external interrupt pin, the bit of port selection register PSR0 should be set to “1” correspondingly.
Example: To use as an INT0 and INT2
:
;**** Set external interrupt port as pull-up state.
LDM
PU1,#0000_0101B
;
;**** Set port as an external interrupt port
LDM
PSR0,#0000_0101B
;
;**** Set Falling-edge Detection
LDM
IEDS,#0001_0001B
:
max. 12 fXIN
Interrupt Interrupt
goes
latched
active
Response Time
The INT0 ~ INT3 edge are latched into INT0IF ~ INT3IF at every
machine cycle. The values are not actually polled by the circuitry
until the next machine cycle. If a request is active and conditions
are right for it to be acknowledged, a hardware subroutine call to
the requested service routine will be the next instruction to be executed. The DIV itself takes twelve cycles. Thus, a minimum of
twelve complete machine cycles elapse between activation of an
external interrupt request and the beginning of execution of the
first instruction of the service routine.
Figure 17-8 shows interrupt response timings.
8 fXIN
Interrupt
processing
Interrupt
routine
Figure 17-8 Interrupt Response Timing Diagram
84
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
MSB
W
IEDS
W
W
W
W
W
W
LSB
W
IED3H IED3L IED2H IED2L IED1H IED1L IED0H IED0L
BTCL
INT3
INT2
INT1
ADDRESS: 0EEH
INITIAL VALUE: 00H
INT0
Edge selection register
00: Reserved
01: Falling (1-to-0 transition)
10: Rising (0-to-1 transition)
11: Both (Rising & Falling)
W
PSR0
W
W
PWM3O PWM1O EC1E
MSB
0: R11
1: PWM3O
W
W
W
W
W
EC0E BTCL INT2E INT1E INT0E
INT3E
ADDRESS: 0F8H
INITIAL VALUE: 00H
LSB
0: R11
1: INT0
0: R10
1: PWM1O
0: R07
1: EC1
0: R12
1: INT1
0: R04
1: EC0
0: R00
1: INT3
0: R03
1: INT2
Figure 17-9 IEDS register and Port Selection Register PSR0
August 18, 2009 Ver 1.02
www.DataSheet.in
85
MC80F0704/0708/0804/0808
18. POWER SAVING OPERATION
The MC80F0704/0708/0804/0808 has two power-down modes.
In power-down mode, power consumption is reduced
considerably. For applications where power consumption is a
critical factor, device provides two kinds of power saving func-
tions, STOP mode and SLEEP mode. Table 18-1 shows the status
of each Power Saving Mode. SLEEP mode is entered by the
SSCR register to “0Fh”., and STOP mode is entered by STOP instruction after the SSCR register to “5Ah”.
18.1 Sleep Mode
In this mode, the internal oscillation circuits remain active.
Oscillation continues and peripherals are operate normally but
CPU stops. Movement of all peripherals is shown in Table 18-1.
SLEEP mode is entered by setting the SSCR register to “0Fh”. It
W
7
W
6
W
5
W
4
W
3
SSCR
is released by Reset or interrupt. To be released by interrupt, interrupt should be enabled before SLEEP mode.
W
2
W
1
W
0
ADDRESS: 0F5H
INITIAL VALUE: 0000 0000B
Power Down Control
5AH: STOP mode
0FH: SLEEP mode
NOTE :
To get into STOP mode, SSCR must be set to 5AH just before STOP instruction execution.
At STOP mode, Stop & Sleep Control Register (SSCR) value is cleared automatically when released.
To get into SLEEP mode, SSCR must be set to 0FH.
Figure 18-1 STOP and SLEEP Control Register
Release the SLEEP mode
The exit from SLEEP mode is hardware reset or all interrupts.
Reset re-defines all the Control registers but does not change the
on-chip RAM. Interrupts allow both on-chip RAM and Control
registers to retain their values.
If I-flag = 1, the normal interrupt response takes place. If I-flag =
0, the chip will resume execution starting with the instruction following the SLEEP instruction. It will not vector to interrupt service routine. (refer to Figure 18-4 )
86
www.DataSheet.in
When exit from SLEEP mode by reset, enough oscillation stabilizing time is required to normal operation. Figure 18-3 shows
the timing diagram. When released from the SLEEP mode, the
Basic interval timer is activated on wake-up. It is increased from
00H until FFH. The count overflow is set to start normal operation. Therefore, before SLEEP instruction, user must be set its
relevant prescaler divide ratio to have long enough time (more
than 20msec). This guarantees that oscillator has started and stabilized. By interrupts, exit from SLEEP mode is shown in Figure
18-2 . By reset, exit from SLEEP mode is shown in Figure 18-3 .
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
.
~
~
~ ~
~ ~
Internal Clock
~ ~
~ ~
~ ~
~ ~
Oscillator
(XIN pin)
SLEEP Instruction
Executed
Normal Operation
SLEEP Operation
~
~
External Interrupt
Normal Operation
Figure 18-2 SLEEP Mode Release Timing by External Interrupt
~
~
~
~
Oscillator
(XIN pin)
~
~
CPU
Clock
~
~
Internal
RESET
~
~
~
~
RESET
~
~
SLEEP Instruction
Execution
Normal Operation
Stabilization Time
tST = 65.5mS @4MHz
Normal Operation
SLEEP Operation
Figure 18-3 Timing of SLEEP Mode Release by Reset
18.2 Stop Mode
In the Stop mode, the main oscillator, system clock and peripheral clock is stopped, but RC-oscillated watchdog timer continue to
operate. With the clock frozen, all functions are stopped, but the
on-chip RAM and Control registers are held. The port pins out the
values held by their respective port data register, port direction
registers. Oscillator stops and the systems internal operations are
all held up.
• The states of the RAM, registers, and latches valid
immediately before the system is put in the STOP
state are all held.
• The program counter stop the address of the
instruction to be executed after the instruction
" STOP " which starts the STOP operating mode.
August 18, 2009 Ver 1.02
www.DataSheet.in
Note: The Stop mode is activated by execution of STOP instruction after setting the SSCR to “5AH”. (This register should be written by byte operation. If this register is set by bit manipulation
instruction, for example " set1 " or " clr1 " instruction, it may be undesired operation)
In the Stop mode of operation, VDD can be reduced to minimize
power consumption. Care must be taken, however, to ensure that
VDD is not reduced before the Stop mode is invoked, and that
VDD is restored to its normal operating level, before the Stop
mode is terminated.
The reset should not be activated before VDD is restored to its
normal operating level, and must be held active long enough to
allow the oscillator to restart and stabilize.
87
MC80F0704/0708/0804/0808
Note: After STOP instruction, at least two or more NOP instruction should be written.
Ex)
LDM CKCTLR,#0FH ;more than 20ms
LDM SSCR,#5AH
STOP
NOP ;for stabilization time
NOP ;for stabilization time
In the STOP operation, the dissipation of the power associated
with the oscillator and the internal hardware is lowered; however,
the power dissipation associated with the pin interface (depending on the external circuitry and program) is not directly determined by the hardware operation of the STOP feature. This point
should be little current flows when the input level is stable at the
power voltage level (VDD/VSS); however, when the input level
gets higher than the power voltage level (by approximately 0.3 to
0.5V), a current begins to flow. Therefore, if cutting off the output transistor at an I/O port puts the pin signal into the high-impedance state, a current flow across the ports input transistor,
requiring to fix the level by pull-up or other means.
Peripheral
STOP Mode
SLEEP Mode
CPU
Stop
Stop
RAM
Retain
Retain
Basic Interval Timer
Halted
Operates Continuously
Watchdog Timer
Stop (Only operates in RC-WDT mode)
Stop
Timer/Counter
Halted (Only when the event counter mode
is enabled, timer operates normally)
Operates Continuously
Buzzer, ADC
Stop
Stop
SIO
Only operate with external clock
Only operate with external clock
Oscillator
Stop (XIN=L, XOUT=H)
Oscillation
I/O Ports
Retain
Retain
Control Registers
Retain
Retain
Internal Circuit
Stop mode
Sleep mode
Prescaler
Retain
Active
Address Data Bus
Retain
Retain
Release Source
Reset, Timer(EC0,1), SIO (ext. clock),
Watchdog Timer (RC-WDT mode),
External Interrupt
Reset, All Interrupts
Table 18-1 Peripheral Operation During Power Saving Mode
Release the STOP mode
routine. (refer to Figure 18-4 )
The source for exit from STOP mode is hardware reset, external
interrupt, Timer(EC0,1), WDT, SIO. When releasing from the
STOP mode by the SIO(ext.clock), the SIOR has dummy data
and the SIOST bit should be cleared after release from the STOP
mode.
When exit from Stop mode by external interrupt, enough oscillation stabilizing time is required to normal operation. Figure 18-5
shows the timing diagram. When released from the Stop mode,
the Basic interval timer is activated on wake-up. It is increased
from 00H until FFH. The count overflow is set to start normal operation. Therefore, before STOP instruction, user must be set its
relevant prescaler divide ratio to have long enough time (more
than 20msec). This guarantees that oscillator has started and stabilized.
Reset re-defines all the Control registers but does not change the
on-chip RAM. External interrupts allow both on-chip RAM and
Control registers to retain their values.
If I-flag = 1, the normal interrupt response takes place. If I-flag =
0, the chip will resume execution starting with the instruction following the STOP instruction. It will not vector to interrupt service
88
www.DataSheet.in
By reset, exit from Stop mode is shown in Figure 18-6 .
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
STOP
INSTRUCTION
STOP Mode
Interrupt Request
Corresponding Interrupt
Enable Bit (IENH, IENL)
=0
IENH or IENL ?
=1
STOP Mode Release
Master Interrupt
Enable Bit PSW[2]
I-FLAG
=0
=1
Interrupt Service Routine
Next
INSTRUCTION
Figure 18-4 STOP Releasing Flow by Interrupts
.
~ ~
~ ~
~
~
Oscillator
(XIN pin)
~
~
~
~
Internal Clock
~
~
STOP Instruction
Executed
n+1 n+2
n+3
0
Clear
Normal Operation
Stop Operation
1
~ ~
~ ~
n
~ ~
~ ~
BIT Counter
~
~
External Interrupt
FE
Stabilization Time
tST & gt; 20ms
by software
FF
0
1
2
Normal Operation
Before executing Stop instruction, Basic Interval Timer must be set
properly by software to get stabilization time which is longer than 20ms.
Figure 18-5 STOP Mode Release Timing by External Interrupt
August 18, 2009 Ver 1.02
www.DataSheet.in
89
MC80F0704/0708/0804/0808
STOP Mode
~
~
~ ~
~ ~
~
~
~
~
Internal
RESET
~
~
RESET
~
~
Internal
Clock
~ ~
~ ~
Oscillator
(XI pin)
STOP Instruction Execution
Time can not be control by software
Stabilization Time
tST = 65.5mS @4MHz
Figure 18-6 Timing of STOP Mode Release by Reset
18.3 Stop Mode at Internal RC-Oscillated Watchdog Timer Mode
In the Internal RC-Oscillated Watchdog Timer mode, the on-chip
oscillator is stopped. But internal RC oscillation circuit is oscillated in this mode. The on-chip RAM and Control registers are
held. The port pins out the values held by their respective port
data register, port direction registers.
The Internal RC-Oscillated Watchdog Timer mode is activated
by execution of STOP instruction after setting the bit RCWDT of
CKCTLR to " 1 " . (This register should be written by byte operation. If this register is set by bit manipulation instruction, for example " set1 " or " clr1 " instruction, it may be undesired operation)
Note: Caution: After STOP instruction, at least two or more NOP
instruction should be written
Ex)
LDM WDTR,#1111_1111B
LDM CKCTLR,#0010_1110B
LDM SSCR,#0101_1010B
STOP
NOP
;for stabilization time
NOP
;for stabilization time
The exit from Internal RC-Oscillated Watchdog Timer mode is
hardware reset or external interrupt or watchdog timer interrupt
90
www.DataSheet.in
(at RC-watchdog timer mode). Reset re-defines all the Control
registers but does not change the on-chip RAM. External interrupts allow both on-chip RAM and Control registers to retain
their values.
If I-flag = 1, the normal interrupt response takes place. In this
case, if the bit WDTON of CKCTLR is set to " 0 " and the bit
WDTE of IENH is set to " 1 " , the device will execute the watchdog timer interrupt service routine(Figure 8-6 ). However, if the
bit WDTON of CKCTLR is set to " 1 " , the device will generate
the internal Reset signal and execute the reset processing(Figure
18-8 ). If I-flag = 0, the chip will resume execution starting with
the instruction following the STOP instruction. It will not vector
to interrupt service routine.(refer to Figure 18-4 )
When exit from Stop mode at Internal RC-Oscillated Watchdog
Timer mode by external interrupt, the oscillation stabilization
time is required to normal operation. Figure 18-7 shows the timing diagram. When release the Internal RC-Oscillated Watchdog
Timer mode, the basic interval timer is activated on wake-up. It
is increased from 00H until FFH. The count overflow is set to start
normal operation. Therefore, before STOP instruction, user must
be set its relevant prescaler divide ratio to have long enough time
(more than 20msec). This guarantees that oscillator has started
and stabilized. By reset, exit from internal RC-Oscillated Watchdog Timer mode is shown in Figure 18-8 .
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
~
~
~
~
~
~
Oscillator
(XIN pin)
Internal
RC Clock
~
~
~
~
Internal
Clock
~
~
External
Interrupt
( or WDT Interrupt )
~
~
STOP Instruction Execution
~
~
N-2
N-1
N
N+1
N+2
00
01
FE
FF
00
00
~
~
BIT
Counter
Clear Basic Interval Timer
Normal Operation
STOP mode
at RC-WDT Mode
Stabilization Time
tST & gt; 20mS
Normal Operation
Figure 18-7 Stop Mode Release at Internal RC-WDT Mode by External Interrupt or WDT Interrupt
RCWDT Mode
~
~
~
~
~
~
Oscillator
(XIN pin)
Internal
RC Clock
~
~
~
~
Internal
Clock
~
~
Internal
RESET
~
~
~
~
RESET
RESET by WDT
Time can not be control by software
~
~
STOP Instruction Execution
Stabilization Time
tST = 65.5mS @4MHz
Figure 18-8 Internal RC-WDT Mode Releasing by Reset
August 18, 2009 Ver 1.02
www.DataSheet.in
91
MC80F0704/0708/0804/0808
18.4 Minimizing Current Consumption
The Stop mode is designed to reduce power consumption. To
minimize current drawn during Stop mode, the user should turn-
off output drivers that are sourcing or sinking current, if it is practical.
VDD
INPUT PIN
INPUT PIN
VDD
VDD
internal
pull-up
VDD
i=0
OPEN
O
i
GND
O
i
Very weak current flows
VDD
X
X
i=0
O
OPEN
Weak pull-up current flows
GND
O
When port is configured as an input, input level should
be closed to 0V or 5V to avoid power consumption.
Figure 18-9 Application Example of Unused Input Port
OUTPUT PIN
OUTPUT PIN
VDD
ON
OPEN
OFF
ON
OFF
X
O
OFF
VDD
ON
OFF
L
ON
i
GND
VDD
L
OFF
ON
i
GND
GND
X
O
i=0
O
In the left case, Tr. base current flows from port to GND.
To avoid power consumption, there should be low output
to the port .
In the left case, much current flows from port to GND.
Figure 18-10 Application Example of Unused Output Port
pull-up or other means.
Note: In the STOP operation, the power dissipation associated
with the oscillator and the internal hardware is lowered; however,
the power dissipation associated with the pin interface (depending
on the external circuitry and program) is not directly determined by
the hardware operation of the STOP feature. This point should be
little current flows when the input level is stable at the power voltage level (VDD/VSS); however, when the input level becomes higher than the power voltage level (by approximately 0.3V), a current
begins to flow. Therefore, if cutting off the output transistor at an I/
O port puts the pin signal into the high-impedance state, a current
flow across the ports input transistor, requiring it to fix the level by
92
www.DataSheet.in
It should be set properly in order that current flow through port
doesn't exist.
First consider the port setting to input mode. Be sure that there is
no current flow after considering its relationship with external
circuit. In input mode, the pin impedance viewing from external
MCU is very high that the current doesn’t flow.
But input voltage level should be VSS or VDD. Be careful that if
unspecified voltage, i.e. if uncertain voltage level (not VSS or
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
VDD) is applied to input pin, there can be little current (max. 1mA
at around 2V) flow.
If it is not appropriate to set as an input mode, then set to output
mode considering there is no current flow. The port setting to
High or Low is decided by considering its relationship with exter-
August 18, 2009 Ver 1.02
www.DataSheet.in
nal circuit. For example, if there is external pull-up resistor then
it is set to output mode, i.e. to High, and if there is external pulldown register, it is set to low.
93
MC80F0704/0708/0804/0808
19. RESET
The MC80F0704/0708/0804/0808 supports various kinds of reset
as below.
• Watchdog Timer Timeout Reset
• Power-On Reset (POR)
• Address Fail Reset
• Power-Fail Detection (PFD) Reset
• RESET (external reset circuitry)
RESET
Noise Canceller
POR
(Power-On Reset)
S
Address Fail reset
Overflow
PFD
(Power-Fail Detection)
Q
Internal
RESET
R
Clear
WDT
(WDT Timeout Reset)
BIT
Figure 19-1 RESET Block Diagram
The on-chip POR circuit holds down the device in RESET until
VDD has reached a high enough level for proper operation. It will
eliminate external components such as reset IC or external resistor and capacitor for external reset circuit. In addition that the RESET pin can be used to normal input port R35 by setting “POR”
On-chip Hardware
Program counter
RAM page register
G-flag
Operation mode
Initial Value
and “R35EN” bit Configuration Area(20FFH) in the Flash programming. When the device starts normal operation, its operating
parameters (voltage, frequency, temperature...etc) must be met.
.Table 19-1 shows on-chip hardware initialization by reset action.
On-chip Hardware
Initial Value
(FFFFH) - (FFFEH)
Peripheral clock
Off
(RPR)
0
Watchdog timer
Disable
(G)
0
Control registers
Refer to Table 8-1 on page 29
(PC)
Main-frequency clock
Power fail detector
Disable
Table 19-1 Initializing Internal Status by Reset Action
The reset input is the RESET pin, which is the input to a Schmitt
Trigger. A reset in accomplished by holding the RESET pin low
for at least 8 oscillator periods, within the operating voltage range
and oscillation stable, it is applied, and the internal state is initialized. After reset, 65.5ms (at 4 MHz) add with 7 oscillator periods
are required to start execution as shown in Figure 19-3 .
Internal RAM is not affected by reset. When VDD is turned on,
the RAM content is indeterminate. Therefore, this RAM should
be initialized before read or tested it.
When the RESET pin input goes to high, the reset operation is released and the program execution starts at the vector address
stored at addresses FFFEH - FFFFH.
VCC
10kΩ
7036P
to the RESET pin
+
10uF
Figure 19-2 Simple Power-on-Reset Circuit
A connection for simple power-on-reset is shown in Figure 19-2 .
94
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
1
?
4
?
5
6
7
~
~
?
FFFE FFFF Start
?
~ ~
~ ~
?
?
?
?
FE
ADL
ADH
OP
~
~
DATA
BUS
3
~
~
RESET
ADDRESS
BUS
2
~
~
Oscillator
(XIN pin)
Stabilization Time
tST =65.5mS at 4MHz
Reset Process Step
tST =
1
fXIN ÷1024
MAIN PROGRAM
x 256
Figure 19-3 Timing Diagram after Reset
The Address Fail Reset is the function to reset the system by
checking code access of abnormal and unwished address caused
by erroneous program code itself or external noise, which could
not be returned to normal operation and would become malfunction state. If the CPU tries to fetch the instruction from ineffective
August 18, 2009 Ver 1.02
www.DataSheet.in
code area or RAM area, the address fail reset is occurred. Please
refer to Figure 11-2 for setting address fail option.
95
MC80F0704/0708/0804/0808
20. POWER FAIL PROCESSOR
The MC80F0704/0708/0804/0808 has an on-chip power fail detection circuitry to immunize against power noise. A configuration register, PFDR, can enable or disable the power fail detect
circuitry. Whenever VDD falls close to or below power fail voltage for 100ns, the power fail situation may reset or freeze MCU
according to PFDM bit of PFDR. Refer to “Figure 20-1 Power
PFDR
7
-
6
-
5
-
4
-
3
-
R/W
2
Fail Voltage Detector Register” on page 96.
In the in-circuit emulator, power fail function is not implemented
and user can not experiment with it. Therefore, after final development of user program, this function may be experimented or
evaluated.
R/W
1
R/W
0
PFDEN PFDM PFDS
ADDRESS: 0F7H
INITIAL VALUE: ---- -000B
Power Fail Status
0: Normal operate
1: Set to “1” if power fail is detected
PFD Operation Mode
0 : MCU will be frozen by power fail detection
1 : MCU will be reset by power fail detection
* Cautions :
PFD Enable Bit
0: Power fail detection disable
1: Power fail detection enable
Be sure to set bits 3 through 7 to “0”.
Figure 20-1 Power Fail Voltage Detector Register
RESET VECTOR
PFDS =1
YES
NO
RAM Clear
Initialize RAM Data
Initialize All Ports
Initialize Registers
PFDS = 0
Skip the
initial routine
Function
Execution
Figure 20-2 Example S/W of Reset flow by Power fail
96
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
VDD
Internal
RESET
VPFDMAX
VPFDMIN
65.5mS
VDD
When PFDM = 1
Internal
RESET
t & lt; 65.5mS
65.5mS
VDD
Internal
RESET
65.5mS
VPFDMAX
VPFDMIN
VPFDMAX
VPFDMIN
Figure 20-3 Power Fail Processor Situations (at 4MHz operation)
August 18, 2009 Ver 1.02
www.DataSheet.in
97
MC80F0704/0708/0804/0808
21. COUNTERMEASURE OF NOISE
21.1 Oscillation Noise Protector
The Oscillation Noise Protector (ONP) is used to supply stable
internal system clock by excluding the noise which could be entered into oscillator and recovery the oscillation fail. This function could be enabled or disabled by the “ONP” bit of the Device
configuration area (20FFH) for the MC80F0704/0708/0804/
0808, “ONP” option bits MASK option.
by high frequency noise.
- Change system clock to the internal oscillation clock
when the high frequency noise is continuing.
- Change system clock to the internal oscillation clock
when the XIN/XOUT is shorted or opened, the main
oscillation is stopped except by stop instruction and
the low frequency noise is entered.
The ONP function is like below.
- Recovery the oscillation wave crushed or loss caused
XIN
OFP
1
HF Noise
Canceller
HF Noise
Observer
XIN_NF
Mux
0S
0
CLK
Changer
Internal
OSC
1
FINTERNAL
S
en
INT_CLK
ONP
OFP
LF Noise
Observer
CLK_CHG
o/f
ONPb = 0
PS10
LF_on = 1
IN_CLK = 0
High Frq. Noise
ONP
IN4(2)MCLK(XO)
en
CK
en
OFP
(8-Bit counter)
INT_CLK 8 periods
(250ns × 8 =2us)
PS10(INT_CLK/512) 256 periods
(250ns × 512 × 256 =33 ms)
~
~
~
~
Low Frq. Noise or
Oscillation Fail
~
~
~
~
INT_CLK reset
Noise Cancel
~
~
XIN_NF
~
~
XIN
~
~
~ ~
~ ~
INT_CLK
OFP_EN
~ ~
~ ~
CHG_END
CLK_CHG
Clock Change Start(XIN to INT_CLK)
~
~
~
~
fINTERNAL
Clock Change End(INT_CLK to XIN))
Figure 21-1 Block Diagram of ONP & OFP and Respective Wave Forms
98
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
21.2 Oscillation Fail Processor
The oscillation fail processor (OFP) can change the clock source
from external to internal oscillator when the oscillation fail occurred. This function could be enabled or disabled by the “OFP”
bit of the Device Configuration Area (MASK option for
MC80F0704/0708/0804/0808.
And this function can recover the external clock source when the
external clock is recovered to normal state.
Configuration Area (MASK option for MC80F0704/0708/0804/
0808 enables the function to operate the device by using the internal oscillator clock in ONP block as system clock. There is no
need to connect the X-tal, resonator, RC and R externally. The
user only to connect the XIN pin to VDD. After selecting the this
option, the period of internal oscillator clock could be checked by
XOUT outputting clock divided the internal oscillator clock by 4.
IN4(2)MCLK/CLKXO(XO) Option
The “IN4MCLK(XO)”, “IN2MCLK(XO)” bit of the Device
August 18, 2009 Ver 1.02
www.DataSheet.in
99
MC80F0704/0708/0804/0808
22. Device Configuration Area
The Device Configuration Area can be programmed or left unprogrammed to select device configuration such as POR, ONP,
CLK option and security bit. This area is not accessible during
normal execution but is readable and writable during FLASH
program / verify mode.
Configuration Option Bits
7
ONP
Note: The Configuration Option may not be read exactly
when VDD rising time is very slow. It is recommended to
adjust the VDD rising time faster than 40ms/V (200ms from
0V to 5V).
6
5
4
3
2
1
0
OFP LOCK POR R35EN CLK2 CLK1 CLK0
ADDRESS: 20FFH
INITIAL VALUE: 00H
Oscillation configuration
000 : IN4MCLK (Internal 4MHz Oscillation & R33/R34 Enable)
001 : IN2MCLK (Internal 2MHz Oscillation & R33/R34 Enable)
010 : EXRC (External R/RC Oscillation & R34 Enable)
011 : X-tal (Crystal or Resonator Oscillation)
100 : IN4MCLKXO (internal 4MHz Oscillation & R33 Enable
& XOUT = fSYS ÷ 4)
101 : IN2MCLKXO (internal 2MHz Oscillation & R33 Enable
& XOUT = fSYS ÷ 4)
110 : EXRCXO (External R/RC Oscillation & XOUT = fSYS ÷ 4)
111 : Prohibited
RESET/R35 Port configuration
0 : R35 Port Disable (Use RESET)
1 : R35 Port Enable (Disable RESET)
POR Use
0 : Disable POR Reset
1 : Enable POR Reset
Security Bit
0 : Enable reading User Code
1 : Disable reading User Code
OFP use
0 : Disable OFP (Clock Changer)
1 : Enable OFP (Clock Changer)
ONP disable
0 : Enable ONP (Enable OFP, Internal 4MHz/2MHz oscillation)
1 : Disable ONP (Disable OFP, Internal 4MHz/2MHz oscillation)
Figure 22-1 Device Configuration Area
100
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
23. Emulator EVA. Board Setting
➎
➋
➏
➐
➌
➍
➊
August 18, 2009 Ver 1.02
www.DataSheet.in
101
MC80F0704/0708/0804/0808
DIP Switch and VR Setting
configuration
Before execute the user program, keep in your mind the below
DIP S/W
➊
➋
Description
ON/OFF Setting
-
This connector is only used for a device over 32 PIN.
For the MC80F0224/MC80F0448
-
This connector is only used for a device under 32 PIN.
For the MC80F0708/0808.
Must be OFF position.
ON
1
ON : For the MC80F0224/MC80F0448.
OFF : For the MC80F0708/0808.
Eva. select switch
ON
OFF
OFF
2
3
ON
Use Eva. VDD
➌
Use User’s AVDD
These switches select the AVDD source.
ON & OFF : Use Eva. VDD
OFF & ON : Use User AVDD
AVDD pin select switch
This switch select the /Reset source.
Normally OFF.
EVA. chip can be reset by external user target board.
ON : Reset is available by either user target
system board or Emulator RESET switch.
OFF : Reset the MCU by Emulator RESET
switch. Does not work from user target
board.
This switch select the Xout signal on/off.
Normally OFF.
MCU XOUT pin is disconnected internally
in the Emulator. Some circumstance user
may connect this circuit.
ON : Output XOUT signal
OFF : Disconnect circuit
SW2
4
5
This switch select Eva. B/D Power supply source.
MDS
➍
SW3
MDS
Normally MDS.
This switch select Eva. B/D Power supply
source.
1
USER
Use MDS Power
➎
SW4
102
www.DataSheet.in
1
2
USER
Use User’s Power
This switch select the R22 or SXOUT.
This switch select the R21 or SXIN.
These switchs select the Normal I/O
port(off) or Sub-Clock (on).
It is reserved for the MC80F0448.
ON : SXOUT, SXIN
OFF : R22, R21
Don’t care (MC80F0224/MC80F0448).
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
DIP S/W
Description
SW5
➐
These switches select the R33 or XIN
3
4
These switches select the R34 or XOUT
5
6
➏
1
2
These switches select the R35 or /Reset
-
This is External oscillation socket(CAN Type. OSC)
August 18, 2009 Ver 1.02
www.DataSheet.in
ON/OFF Setting
This switch select the Normal I/O port
(on & off) or special function select(off & on).
It is reserved for the MC80F0708/0808.
ON & OFF : R33,R34,R35 Port selected.
OFF & ON : XOUT, XIN , /Reset selected.
Don’t care (MC80F0224/MC80F0448).
This is for External Clock (CAN Type.
OSC).
103
MC80F0704/0708/0804/0808
104
www.DataSheet.in
August 18, 2009 Ver 1.02
www.DataSheet.in
APPENDIX
MC80F0704/0708/0804/0808
A. INSTRUCTION
A.1 Terminology List
Terminology
Description
A
Accumulator
X
X - register
Y
Y - register
PSW
Program Status Word
#imm
8-bit Immediate data
dp
Direct Page Offset Address
!abs
Absolute Address
[]
Indirect expression
{}
Register Indirect expression
{ }+
Register Indirect expression, after that, Register auto-increment
.bit
Bit Position
A.bit
Bit Position of Accumulator
dp.bit
Bit Position of Direct Page Memory
M.bit
rel
upage
Bit Position of Memory Data (000H~0FFFH)
Relative Addressing Data
U-page (0FF00H~0FFFFH) Offset Address
n
Table CALL Number (0~15)
+
Addition
Upper Nibble Expression in Opcode
0
x
Bit Position
Upper Nibble Expression in Opcode
1
y
Bit Position
−
Subtraction
×
Multiplication
/
Division
()
Contents Expression
∧
AND
∨
OR
⊕
Exclusive OR
~
NOT
←
Assignment / Transfer / Shift Left
→
Equal
≠
www.DataSheet.in
Exchange
=
ii
Shift Right
↔
Not Equal
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
A.2 Instruction Map
LOW 00000
00
HIGH
00001
01
00010
02
00011
03
00101
05
00110
06
00111
07
01000
08
01001
09
01010
0A
01011
0B
01100
0C
01101
0D
01110
0E
01111
0F
ADC
#imm
ADC
dp
ADC
dp+X
ADC
!abs
ASL
A
ASL
dp
TCALL
0
SETA1
.bit
BIT
dp
POP
A
PUSH
A
BRK
000
-
SET1
dp.bit
001
CLRC
“
“
“
SBC
#imm
SBC
dp
SBC
dp+X
SBC
!abs
ROL
A
ROL
dp
TCALL CLRA1
2
.bit
COM
dp
POP
X
PUSH
X
BRA
rel
010
CLRG
“
“
“
CMP
#imm
CMP
dp
CMP
dp+X
CMP
!abs
LSR
A
LSR
dp
TCALL
4
NOT1
M.bit
TST
dp
POP
Y
PUSH
Y
PCALL
Upage
011
DI
“
“
“
OR
#imm
OR
dp
OR
dp+X
OR
!abs
ROR
A
ROR
dp
TCALL
6
OR1
OR1B
CMPX
dp
POP
PSW
PUSH
PSW
RET
100
CLRV
“
“
“
AND
#imm
AND
dp
AND
dp+X
AND
!abs
INC
A
INC
dp
TCALL AND1
8
AND1B
CMPY
dp
CBNE
dp+X
TXSP
INC
X
101
SETC
“
“
“
EOR
#imm
EOR
dp
EOR
dp+X
EOR
!abs
DEC
A
DEC
dp
TCALL EOR1
10
EOR1B
DBNE
dp
XMA
dp+X
TSPX
DEC
X
110
SETG
“
“
“
LDA
#imm
LDA
dp
LDA
dp+X
LDA
!abs
TXA
LDY
dp
TCALL
12
LDC
LDCB
LDX
dp
LDX
dp+Y
XCN
DAS
(N/A)
111
EI
“
“
“
LDM
dp,#imm
STA
dp
STA
dp+X
STA
!abs
TAX
STY
dp
TCALL
14
STC
M.bit
STX
dp
STX
dp+Y
XAX
STOP
10001
11
10010
12
10011
13
10100
14
10101
15
10110
16
10111
17
11000
18
11001
19
11010
1A
11011
1B
11100
1C
11101
1D
11110
1E
11111
1F
ADC
{X}
ADC
!abs+Y
ADC
[dp+X]
ADC
[dp]+Y
ASL
!abs
ASL
dp+X
TCALL
1
JMP
!abs
BIT
!abs
ADDW
dp
LDX
#imm
JMP
[!abs]
TEST
!abs
SUBW
dp
LDY
#imm
JMP
[dp]
TCLR1 CMPW
!abs
dp
CMPX
#imm
CALL
[dp]
LOW 10000
HIGH
10
BBS
BBS
A.bit,rel dp.bit,rel
00100
04
000
BPL
rel
CLR1
dp.bit
BBC
BBC
A.bit,rel dp.bit,rel
001
BVC
rel
“
“
“
SBC
{X}
SBC
!abs+Y
SBC
[dp+X]
SBC
[dp]+Y
ROL
!abs
ROL
dp+X
TCALL
3
CALL
!abs
010
BCC
rel
“
“
“
CMP
{X}
CMP
!abs+Y
CMP
[dp+X]
CMP
[dp]+Y
LSR
!abs
LSR
dp+X
TCALL
5
MUL
011
BNE
rel
“
“
“
OR
{X}
OR
!abs+Y
OR
[dp+X]
OR
[dp]+Y
ROR
!abs
ROR
dp+X
TCALL
7
DBNE
Y
CMPX
!abs
LDYA
dp
CMPY
#imm
RETI
100
BMI
rel
“
“
“
AND
{X}
AND
!abs+Y
AND
[dp+X]
AND
[dp]+Y
INC
!abs
INC
dp+X
TCALL
9
DIV
CMPY
!abs
INCW
dp
INC
Y
TAY
101
BVS
rel
“
“
“
EOR
{X}
EOR
!abs+Y
EOR
[dp+X]
EOR
[dp]+Y
DEC
!abs
DEC
dp+X
TCALL
11
XMA
{X}
XMA
dp
DECW
dp
DEC
Y
TYA
110
BCS
rel
“
“
“
LDA
{X}
LDA
!abs+Y
LDA
[dp+X]
LDA
[dp]+Y
LDY
!abs
LDY
dp+X
TCALL
13
LDA
{X}+
LDX
!abs
STYA
dp
XAY
DAA
(N/A)
111
BEQ
rel
“
“
“
STA
{X}
STA
!abs+Y
STA
[dp+X]
STA
[dp]+Y
STY
!abs
STY
dp+X
TCALL
15
STA
{X}+
STX
!abs
CBNE
dp
XYX
NOP
August 18, 2009 Ver 1.02
www.DataSheet.in
iii
MC80F0704/0708/0804/0808
A.3 Instruction Set
Arithmetic / Logic Operation
NO.
MNEMONIC
OP
CODE
04
BYTE
NO
2
CYCLE
NO
2
1
ADC #imm
2
ADC dp
05
2
3
3
ADC dp + X
06
2
4
4
ADC !abs
07
3
4
5
ADC !abs + Y
15
3
5
6
ADC [ dp + X ]
16
2
6
7
ADC [ dp ] + Y
17
2
6
8
ADC { X }
14
1
3
9
AND #imm
AND dp
84
2
2
85
2
FLAG
NVGBHIZC
OPERATION
3
10
11
AND dp + X
86
2
AND !abs
87
3
4
13
AND !abs + Y
95
3
5
14
AND [ dp + X ]
96
2
AND [ dp ] + Y
97
2
AND { X }
94
1
3
17
ASL A
08
1
2
18
19
ASL dp
ASL dp + X
09
19
2
2
4
5
20
ASL !abs
18
3
5
21
CMP #imm
44
2
2
22
CMP dp
45
2
3
23
CMP dp + X
46
2
4
24
CMP !abs
47
3
4
25
CMP !abs + Y
55
3
5
26
CMP [ dp + X ]
56
2
6
27
CMP [ dp ] + Y
57
2
6
28
CMP { X }
54
1
3
29
CMPX #imm
5E
2
2
30
CMPX dp
6C
2
3
31
CMPX !abs
7C
3
4
32
CMPY #imm
7E
2
2
33
CMPY dp
8C
2
3
34
CMPY !abs
9C
3
4
35
COM dp
2C
2
36
DAA
-
37
DAS
38
N-----Z-
6
16
Logical AND
A← (A)∧(M)
6
15
NV--H-ZC
4
12
Add with carry.
A←(A)+(M)+C
Arithmetic shift left
C
7
6
5
4
3
2
1
0
N-----ZC
“0”
Compare accumulator contents with memory contents
(A) -(M)
N-----ZC
Compare X contents with memory contents
(X)-(M)
N-----ZC
Compare Y contents with memory contents
(Y)-(M)
N-----ZC
4
1’S Complement : ( dp ) ← ~( dp )
N-----Z-
-
-
Unsupported
-
-
-
-
Unsupported
-
DEC A
A8
1
2
39
DEC dp
A9
2
4
40
DEC dp + X
B9
2
5
41
DEC !abs
B8
3
5
Decrement
M← (M)-1
N-----Z-
42
DEC X
AF
1
2
43
DEC Y
BE
1
2
44
DIV
9B
1
12
Divide : YA / X Q: A, R: Y
NV--H-Z-
iv
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
NO.
MNEMONIC
OP
CODE
A4
BYTE
NO
2
CYCLE
NO
2
FLAG
NVGBHIZC
3
OPERATION
45
EOR #imm
46
EOR dp
A5
2
47
EOR dp + X
A6
2
4
48
EOR !abs
A7
3
4
Exclusive OR
49
EOR !abs + Y
B5
3
5
A← (A)⊕(M)
N-----Z-
50
EOR [ dp + X ]
B6
2
6
51
EOR [ dp ] + Y
B7
2
6
52
EOR { X }
B4
1
3
53
INC A
88
1
2
54
INC dp
89
2
4
55
INC dp + X
99
2
5
Increment
56
INC !abs
98
3
5
M← (M)+1
57
INC X
8F
1
2
58
INC Y
9E
1
2
59
LSR A
48
1
2
60
LSR dp
49
2
4
61
LSR dp + X
59
2
5
62
LSR !abs
58
3
5
63
MUL
5B
1
9
64
OR #imm
64
2
2
65
OR dp
65
2
3
66
OR dp + X
66
2
4
67
OR !abs
67
3
4
68
OR !abs + Y
75
3
5
69
OR [ dp + X ]
76
2
6
70
OR [ dp ] + Y
77
2
6
71
OR { X }
74
1
3
72
ROL A
28
1
2
73
ROL dp
29
2
4
74
ROL dp + X
39
2
5
75
ROL !abs
38
3
5
76
ROR A
68
1
2
77
ROR dp
69
2
4
78
ROR dp + X
79
2
5
79
ROR !abs
78
3
5
80
SBC #imm
24
2
2
81
SBC dp
25
2
3
82
SBC dp + X
26
2
4
83
SBC !abs
27
3
4
84
SBC !abs + Y
35
3
5
85
SBC [ dp + X ]
36
2
6
86
SBC [ dp ] + Y
37
2
6
87
SBC { X }
34
1
3
88
TST dp
4C
2
3
Test memory contents for negative or zero
( dp ) - 00H
N-----Z-
89
XCN
CE
1
5
Exchange nibbles within the accumulator
A7~A4 ↔ A3~A0
N-----Z-
August 18, 2009 Ver 1.02
www.DataSheet.in
N-----Z-
Logical shift right
7
6
5
4
3
2
1
0
C
N-----ZC
“0”
Multiply : YA ← Y × A
N-----Z-
Logical OR
N-----Z-
A ← (A)∨(M)
Rotate left through carry
C
7
6
5
4
3
2
1
0
N-----ZC
Rotate right through carry
7
6
5
4
3
2
1
0
C
N-----ZC
Subtract with carry
NV--HZC
A ← ( A ) - ( M ) - ~( C )
v
MC80F0704/0708/0804/0808
Register / Memory Operation
NO.
MNEMONIC
OP
CODE
C4
BYTE
NO
2
CYCLE
NO
2
OPERATION
1
LDA #imm
2
LDA dp
C5
2
3
3
LDA dp + X
C6
2
4
4
LDA !abs
C7
3
4
Load accumulator
5
LDA !abs + Y
D5
3
5
A←(M)
6
LDA [ dp + X ]
D6
2
6
7
LDA [ dp ] + Y
D7
2
6
8
LDA { X }
D4
1
FLAG
NVGBHIZC
3
N-----Z-
9
LDA { X }+
DB
1
4
X- register auto-increment : A ← ( M ) , X ← X + 1
10
LDM dp,#imm
E4
3
5
Load memory with immediate data : ( M ) ← imm
11
LDX #imm
1E
2
2
12
LDX dp
CC
2
3
Load X-register
13
LDX dp + Y
CD
2
4
X ←(M)
14
LDX !abs
DC
3
4
15
LDY #imm
3E
2
2
16
LDY dp
C9
2
3
Load Y-register
17
LDY dp + X
D9
2
4
Y←(M)
18
LDY !abs
D8
3
4
19
STA dp
E5
2
4
20
STA dp + X
E6
2
5
21
STA !abs
E7
3
5
22
STA !abs + Y
F5
3
6
23
STA [ dp + X ]
F6
2
7
24
STA [ dp ] + Y
F7
2
7
25
STA { X }
F4
1
4
26
STA { X }+
FB
1
4
27
STX dp
EC
2
4
28
STX dp + Y
ED
2
5
29
STX !abs
FC
3
5
30
STY dp
E9
2
4
31
STY dp + X
F9
2
5
32
STY !abs
F8
3
5
33
TAX
E8
1
2
Transfer accumulator contents to X-register : X ← A
N-----Z-
34
TAY
9F
1
2
Transfer accumulator contents to Y-register : Y ← A
N-----Z-
35
TSPX
AE
1
2
Transfer stack-pointer contents to X-register : X ← sp
N-----Z-
36
TXA
C8
1
2
Transfer X-register contents to accumulator: A ← X
N-----Z-
37
TXSP
8E
1
2
Transfer X-register contents to stack-pointer: sp ← X
N-----Z-
38
TYA
BF
1
2
Transfer Y-register contents to accumulator: A ← Y
N-----Z-
39
XAX
EE
1
4
Exchange X-register contents with accumulator :X ↔ A
--------
40
XAY
DE
1
4
Exchange Y-register contents with accumulator :Y ↔ A
--------
41
XMA dp
BC
2
5
Exchange memory contents with accumulator
42
XMA dp+X
AD
2
6
43
XMA {X}
BB
1
5
44
XYX
FE
1
4
vi
www.DataSheet.in
--------
N-----Z-
N-----Z-
Store accumulator contents in memory
(M)←A
--------
X- register auto-increment : ( M ) ← A, X ← X + 1
Store X-register contents in memory
(M)← X
Store Y-register contents in memory
(M)← Y
(M)↔A
--------
--------
N-----Z-
Exchange X-register contents with Y-register : X ↔ Y
August 18, 2009 Ver 1.02
--------
MC80F0704/0708/0804/0808
16-BIT Operation
NO.
MNEMONIC
OP
CODE
BYTE
NO
CYCLE
NO
FLAG
NVGBHIZC
OPERATION
1
ADDW dp
1D
2
5
16-Bits add without carry
YA ← ( YA ) + ( dp +1 ) ( dp )
2
CMPW dp
5D
2
4
Compare YA contents with memory pair contents :
(dp+1)(dp)
3
DECW dp
BD
2
6
Decrement memory pair
( dp+1)( dp) ← ( dp+1) ( dp) - 1
N-----Z-
4
INCW dp
9D
2
6
Increment memory pair
( dp+1) ( dp) ← ( dp+1) ( dp ) + 1
N-----Z-
5
LDYA dp
7D
2
5
Load YA
YA ← ( dp +1 ) ( dp )
N-----Z-
6
STYA dp
DD
2
5
Store YA
( dp +1 ) ( dp ) ← YA
--------
7
SUBW dp
3D
2
5
16-Bits substact without carry
YA ← ( YA ) - ( dp +1) ( dp)
NV--H-ZC
OP
CODE
8B
BYTE
NO
3
CYCLE
NO
4
3
4
Bit AND C-flag and NOT : C ← ( C ) ∧ ~( M .bit )
-------C
Bit test A with memory :
Z ← ( A ) ∧ ( M ) , N ← ( M7 ) , V ← ( M6 )
MM----Z-
NV--H-ZC
(YA) −
N-----ZC
Bit Manipulation
NO.
1
MNEMONIC
AND1 M.bit
FLAG
NVGBHIZC
-------C
OPERATION
Bit AND C-flag : C ← ( C ) ∧ ( M .bit )
2
AND1B M.bit
8B
3
BIT dp
0C
2
4
4
BIT !abs
1C
3
5
5
CLR1 dp.bit
y1
2
4
Clear bit : ( M.bit ) ← “0”
--------
2
2
Clear A bit : ( A.bit )← “0”
--------
6
CLRA1 A.bit
2B
7
CLRC
20
1
2
Clear C-flag : C ← “0”
-------0
8
CLRG
40
1
2
Clear G-flag : G ← “0”
--0-----
9
CLRV
80
1
2
Clear V-flag : V ← “0”
-0--0---
10
EOR1 M.bit
AB
3
5
Bit exclusive-OR C-flag : C ← ( C ) ⊕ ( M .bit )
-------C
11
EOR1B M.bit
AB
3
5
Bit exclusive-OR C-flag and NOT : C ← ( C ) ⊕ ~(M .bit)
-------C
12
LDC M.bit
CB
3
4
Load C-flag : C ← ( M .bit )
-------C
13
LDCB M.bit
CB
3
4
Load C-flag with NOT : C ← ~( M .bit )
-------C
14
NOT1 M.bit
4B
3
5
Bit complement : ( M .bit ) ← ~( M .bit )
--------
15
OR1 M.bit
6B
3
5
Bit OR C-flag : C ← ( C ) ∨ ( M .bit )
-------C
16
OR1B M.bit
6B
3
5
Bit OR C-flag and NOT : C ← ( C ) ∨ ~( M .bit )
-------C
2
4
Set bit : ( M.bit ) ← “1”
--------
17
SET1 dp.bit
x1
18
SETA1 A.bit
0B
2
2
Set A bit : ( A.bit ) ← “1”
--------
19
SETC
A0
1
2
Set C-flag : C ← “1”
-------1
20
SETG
C0
1
2
Set G-flag : G ← “1”
--1-----
21
STC M.bit
EB
3
6
Store C-flag : ( M .bit ) ← C
--------
22
TCLR1 !abs
5C
3
6
Test and clear bits with A :
A - ( M ) , ( M ) ← ( M ) ∧ ~( A )
N-----Z-
23
TSET1 !abs
3C
3
6
Test and set bits with A :
A-(M), (M)← (M)∨(A)
N-----Z-
August 18, 2009 Ver 1.02
www.DataSheet.in
vii
MC80F0704/0708/0804/0808
Branch / Jump Operation
1
BBC A.bit,rel
OP
CODE
y2
2
BBC dp.bit,rel
y3
3
5/7
3
BBS A.bit,rel
x2
2
4/6
4
BBS dp.bit,rel
x3
3
5/7
5
BCC rel
50
2
2/4
6
BCS rel
D0
2
2/4
7
BEQ rel
F0
2
2/4
8
BMI rel
90
2
2/4
9
BNE rel
70
2
2/4
10
BPL rel
10
2
2/4
11
BRA rel
2F
2
4
12
BVC rel
30
2
2/4
13
BVS rel
B0
2
2/4
14
CALL !abs
3B
3
8
15
CALL [dp]
5F
2
8
16
CBNE dp,rel
FD
3
5/7
17
CBNE dp+X,rel
8D
3
6/8
18
NO.
MNEMONIC
BYTE
NO
2
CYCLE
NO
4/6
OPERATION
FLAG
NVGBHIZC
Branch if bit clear :
if ( bit ) = 0 , then pc ← ( pc ) + rel
--------
Branch if bit set :
if ( bit ) = 1 , then pc ← ( pc ) + rel
--------
Branch if carry bit clear
if ( C ) = 0 , then pc ← ( pc ) + rel
Branch if carry bit set
if ( C ) = 1 , then pc ← ( pc ) + rel
Branch if equal
if ( Z ) = 1 , then pc ← ( pc ) + rel
Branch if minus
if ( N ) = 1 , then pc ← ( pc ) + rel
Branch if not equal
if ( Z ) = 0 , then pc ← ( pc ) + rel
Branch if minus
if ( N ) = 0 , then pc ← ( pc ) + rel
Branch always
pc ← ( pc ) + rel
Branch if overflow bit clear
if (V) = 0 , then pc ← ( pc) + rel
Branch if overflow bit set
if (V) = 1 , then pc ← ( pc ) + rel
Subroutine call
M( sp)←( pcH ), sp←sp - 1, M(sp)← (pcL), sp ←sp - 1,
if !abs, pc← abs ; if [dp], pcL← ( dp ), pcH← ( dp+1 ) .
----------------------------------------------------------------
--------
Compare and branch if not equal :
if ( A ) ≠ ( M ) , then pc ← ( pc ) + rel.
--------
Decrement and branch if not equal :
if ( M ) ≠ 0 , then pc ← ( pc ) + rel.
--------
Unconditional jump
pc ← jump address
--------
DBNE dp,rel
AC
3
5/7
19
DBNE Y,rel
7B
2
4/6
20
JMP !abs
1B
3
3
21
JMP [!abs]
1F
3
5
22
JMP [dp]
3F
2
4
23
PCALL upage
4F
2
6
U-page call
M(sp) ←( pcH ), sp ←sp - 1, M(sp) ← ( pcL ),
sp ← sp - 1, pcL ← ( upage ), pcH ← ”0FFH” .
--------
24
TCALL n
nA
1
8
Table call : (sp) ←( pcH ), sp ← sp - 1,
M(sp) ← ( pcL ),sp ← sp - 1,
pcL ← (Table vector L), pcH ← (Table vector H)
--------
viii
www.DataSheet.in
August 18, 2009 Ver 1.02
MC80F0704/0708/0804/0808
Control Operation & Etc.
NO.
1
MNEMONIC
BRK
OP
CODE
BYTE
NO
CYCLE
NO
0F
1
8
FLAG
NVGBHIZC
OPERATION
Software interrupt : B ← ”1”, M(sp) ← (pcH), sp ←sp-1,
M(s) ← (pcL), sp ← sp - 1, M(sp) ← (PSW), sp ← sp -1,
pcL ← ( 0FFDEH ) , pcH ← ( 0FFDFH) .
---1-0--
2
DI
60
1
3
Disable interrupts : I ← “0”
-----0--
3
EI
E0
1
3
Enable interrupts : I ← “1”
-----1---------
4
NOP
FF
1
2
No operation
5
POP A
0D
1
4
6
POP X
2D
1
4
7
POP Y
4D
1
4
sp ← sp + 1,
sp ← sp + 1,
sp ← sp + 1,
sp ← sp + 1,
8
POP PSW
6D
1
4
9
PUSH A
0E
1
4
10
PUSH X
2E
1
4
11
PUSH Y
4E
1
4
12
PUSH PSW
6E
1
4
13
RET
6F
1
14
RETI
7F
15
STOP
EF
August 18, 2009 Ver 1.02
www.DataSheet.in
A ← M( sp )
X ← M( sp )
Y ← M( sp )
PSW ← M( sp )
-------restored
M( sp ) ← A , sp ← sp - 1
M( sp ) ← X , sp ← sp - 1
M( sp ) ← Y , sp ← sp - 1
M( sp ) ← PSW , sp ← sp - 1
--------
5
Return from subroutine
sp ← sp +1, pcL ← M( sp ), sp ← sp +1, pcH ← M( sp )
--------
1
6
Return from interrupt
sp ← sp +1, PSW ← M( sp ), sp ← sp + 1,
pcL ← M( sp ), sp ← sp + 1, pcH ← M( sp )
restored
1
3
Stop mode ( halt CPU, stop oscillator )
--------
ix
MC80F0704/0708/0804/0808
x
www.DataSheet.in
August 18, 2009 Ver 1.02